Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0417748 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B506743C03
2.021,0.375 2.5,0.625 0.479,0.25 4.542,0.375 5.021,0.625 0.479,0.25 3.156,0.375 3.635,0.625 0.479,0.25 4.688,0.417 5,0.615 0.313,0.198 10 false H48 3.333,0.417 3.646,0.615 0.313,0.198 10 false M5 2.167,0.417 2.583,0.625 0.417,0.208 10 false A19 2.563,0.417 2.979,0.625 0.417,0.208 10 false *A
*A for Gasoline Model - -


a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
H48-18 (E) - Body ground - Ground Always Below 1 Ω -
H48-4 (+B) - H48-18 (E) Input Power supply Always*1 11 to 14 V -
Ignition switch off*2
H48-15 (CUTB) - H48-18 (E) Input Dark current cut pin*3 Always*1 11 to 14 V -
Ignition switch off*2

·

*1: for Gasoline Model

·

*2: for HV Model

·

*3: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).



c.

Reconnect the H48 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
H48-17 (IG1D) - H48-18 (E) Output IG power supply Ignition switch off → ignition switch ON Below 1 V → 10 V or higher
Power source control

IG Relay Monitor (Outside)


H48-16 (ACCD) - H48-18 (E) Output ACC power supply Ignition switch off → ignition switch ACC Below 1 V → 8.5 V or higher
Power source control

ACC Relay Monitor


M5-17 (CLG1) - H48-18 (E) Output Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


Pulse generation
(See waveform 2)
-
M5-17 (CLG1) - H48-18 (E) Input Input to driver door lock sensor
(front door outside handle assembly (for driver door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Driver door lock sensor touched


Pulse generation
(See waveform 3)
Power source control

D-Door Trigger Switch


M5-17 (CLG1) - H48-18 (E) Input Input to driver door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor touched


Pulse generation
(See waveform 4)
Power source control

D-Door Touch Sensor


M5-16 (CG1B) - H48-18 (E) Output Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


Pulse generation
(See waveform 6)
-
M5-15 (CLG2) - H48-18 (E) Output Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


Pulse generation
(See waveform 2)
-
M5-15 (CLG2) - H48-18 (E) Input Input to front passenger door lock sensor
(front door outside handle assembly (for front passenger door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Front passenger door lock sensor touched


Pulse generation
(See waveform 3)
Power source control

P-Door Trigger Switch


M5-15 (CLG2) - H48-18 (E) Input Input to front passenger door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor touched


Pulse generation
(See waveform 4)
Power source control

P-Door Touch Sensor


M5-14 (CG2B) - H48-18 (E) Output Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


Pulse generation
(See waveform 6)
-
M5-13 (CLG8) - H48-18 (E) Output Output to electrical key antenna (outside luggage compartment) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly → on


Pulse generation
(See waveform 7)
-
M5-12 (CG8B) - H48-18 (E) Output Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly → on


Pulse generation
(See waveform 7)
-
M5-26 (TSW5) - H48-18 (E) Input Back door opener switch assembly (open switch) signal input Back door opener switch assembly (open switch) off → on Pulse generation
(See waveform 8)
Smart Key

Tr/B-Door Unlock SW


M5-27 (TSW6) - H48-18 (E) Input Back door opener switch assembly (lock switch) signal input Back door opener switch assembly (lock switch) off → on Pulse generation
(See waveform 8)
Smart Key

Tr/B-Door Unlock SW


M5-18 (RCO) - H48-18 (E) Output Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 9)
-
M5-19 (RDAM) - H48-18 (E) Input Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
Proceed:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 10)
-
M5-20 (CSEL) - H48-18 (E) Output Communication channel switching circuit Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation -

*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



e.
B340872N01
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection M5-17 (CLG1) - H48-18 (E)
M5-15 (CLG2) - H48-18 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



f.
B340873N01
0.177,1.021 0.635,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection M5-17 (CLG1) - H48-18 (E)
M5-15 (CLG2) - H48-18 (E)
Tool Setting 5 V/DIV., 100 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



g.
B340877C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 0.677,1.917 1.135,2.115 0.458,0.198 10 false *a 1.646,2 1.969,2.156 0.323,0.156 10 false *b 2.615,1.917 3.073,2.115 0.458,0.198 10 false *a
*a Lock sensor not touched
*b Lock sensor touched


Using an oscilloscope, check waveform 3.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection M5-17 (CLG1) - H48-18 (E)
Tool Setting 5 V/DIV., 40 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Driver door lock sensor not touched → touched



Item Content
Tester Connection M5-15 (CLG2) - H48-18 (E)
Tool Setting 5 V/DIV., 40 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Front passenger door lock sensor not touched → touched



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



h.
B340879C02
0.177,1.052 0.635,1.25 0.458,0.198 10 false GND 0.344,1.906 0.802,2.104 0.458,0.198 10 false *a 2.115,1.906 2.573,2.104 0.458,0.198 10 false *a 1.229,1.969 1.667,2.167 0.438,0.198 10 false *b
*a Unlock sensor not touched
*b Unlock sensor touched


Using an oscilloscope, check waveform 4.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection M5-17 (CLG1) - H48-18 (E)
Tool Setting 5 V/DIV., 50 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor not touched → touched



Item Content
Tester Connection M5-15 (CLG2) - H48-18 (E)
Tool Setting 5 V/DIV., 50 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor not touched → touched




i.
B367472N01
0.188,1.021 0.646,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 5.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 5 (Reference)
Item Content
Tester Connection M5-16 (CG1B) - H48-18 (E)
M5-14 (CG2B) - H48-18 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



j.
B367473N01
0.188,1.021 0.646,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 6.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 6 (Reference)
Item Content
Tester Connection M5-16 (CG1B) - H48-18 (E)
M5-14 (CG2B) - H48-18 (E)
Tool Setting 5 V/DIV., 100 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



k.
B340876N01
0.177,1.042 0.635,1.24 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 7.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 7 (Reference)
Item Content
Tester Connection M5-13 (CLG8) - H48-18 (E)
M5-12 (CG8B) - H48-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly → on




l.
B251023C09
1.333,0.49 1.99,0.125 1.99,0.125 2.208,0.125 false 1.99,0.135 1.74,0.51 false 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.25,0.031 2.427,0.208 0.177,0.177 10 false *a
*a Checking for switch on signal at short intervals


Using an oscilloscope, check waveform 8.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 8 (Reference)
Item Content
Tester Connection M5-26 (TSW5) - H48-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Back door opener switch assembly off (open switch) → on

Item Content
Tester Connection M5-27 (TSW6) - H48-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Back door opener switch assembly (lock switch) off → on


m.
B251178C12
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 9.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 9 (Reference)
Item Content
Tester Connection M5-18 (RCO) - H48-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




n.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 10.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 10 (Reference)
Item Content
Tester Connection M5-19 (RDAM) - H48-18 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed





CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B567031N01
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.292,6.198 5.729,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 3.469,7.698 3.781,7.896 0.313,0.198 10 false MB 4.292,0.24 4.604,0.438 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false H42 2.052,1.479 2.365,1.677 0.313,0.198 10 false H43 2.052,1.802 2.365,2 0.313,0.198 10 false H44 0.875,1.083 1.188,1.281 0.313,0.198 10 false 4D 0.875,1.667 1.188,1.865 0.313,0.198 10 false 4C 0.885,2.031 1.198,2.229 0.313,0.198 10 false 4E 0.906,2.26 1.219,2.458 0.313,0.198 10 false 4F 5.854,1.146 6.167,1.344 0.313,0.198 10 false 4B 5.854,1.781 6.167,1.979 0.313,0.198 10 false 4A 1.229,3.302 1.542,3.5 0.313,0.198 10 false H44 3.271,3.271 3.583,3.469 0.313,0.198 10 false H43 5.542,3.26 5.854,3.458 0.313,0.198 10 false H42 1.833,4.625 2.146,4.823 0.313,0.198 10 false 4A 1.24,6.219 1.552,6.417 0.313,0.198 10 false 4C 3.813,6.177 4.125,6.375 0.313,0.198 10 false 4D 6.438,6.24 6.75,6.438 0.313,0.198 10 false 4E 5.427,6.25 5.74,6.448 0.313,0.198 10 false 4F 5.51,4.625 5.823,4.823 0.313,0.198 10 false 4B

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-31 (BECU) - Body ground Input Auxiliary battery power supply (for CPU) Always*1 11 to 14 V
Ignition switch off*2

·

*1: for Gasoline Model

·

*2: for HV Model