Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0417793 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type LH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.


PROCEDURE

Hide 71016A 1.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.
B564061

Install the rear seat cushion frame sub-assembly LH with the 4 nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 72134A 2.INSTALL FRONT INNER SEAT TRACK UPPER RAIL BRACKET LH

a.
B570757

Install the front inner seat track upper rail bracket LH with the 2 nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 71018 3.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH

a.
B569229C01
0,0 0,0 false
V113147

Install in this Direction


Temporarily install the rear seatback frame sub-assembly LH to the No. 1 seat cushion frame sub-assembly LH as shown in the illustration.


b.

Temporarily install the 4 bolts.


c.
B569230

Tighten the 4 bolts while pulling the rear seatback frame sub-assembly LH as shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72308D 4.INSTALL NO. 2 RECLINING CONTROL LINK SUB-ASSEMBLY LH

a.
B564057

Install the No. 2 reclining control link sub-assembly LH with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72308C 5.INSTALL NO. 1 RECLINING CONTROL LINK SUB-ASSEMBLY LH

a.
B564056

Install the No. 1 reclining control link sub-assembly LH with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72704A 6.INSTALL REAR SEAT RECLINING CONTROL CABLE

a.

Route the rear seat reclining control cable as shown in the illustration and engage the clamp.

B564054


b.

Engage the 10 clamps and cable clamp to install the rear seat reclining control cable.

B564053


Hide 72210H 7.INSTALL REAR NO. 1 SEAT TRACK CONTROL CABLE ASSEMBLY LH

a.

Route the rear No. 1 seat track control cable assembly LH as shown in the illustration and engage the 2 clamps.

B564052C01
0,0 0,0 false
V100135

Clamp
V100136

Wire Harness Clamp



b.

Install the rear No. 1 seat track control cable assembly LH with the 2 wire harness clamps.


Hide 8.INSTALL CONNECTOR MALE HOUSING (w/o Seat Heater System)

a.
B571165

w/o Seat Belt Warning System:

i.

Engage the clamp to install the connector male housing.



Hide 82194 9.INSTALL REAR SEAT WIRE LH (w/o Seat Heater System)

a.
B566499

Engage the 7 clamps to install the rear seat wire LH.


Hide 82194 10.INSTALL REAR SEAT WIRE LH (w/ Seat Heater System)

a.
B571164

w/o Seat Belt Warning System:

i.

Engage the 7 clamps to install the rear seat wire LH.



b.
B564051

w/ Seat Belt Warning System:

i.

Engage the 8 clamps to install the rear seat wire LH.



Hide 71691P 11.INSTALL REAR NO. 2 SEAT CUSHION HINGE UPPER COVER RH

a.
B564048C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the claw and guide as shown in the illustration to install the rear No. 2 seat cushion hinge upper cover RH.


Hide 71692M 12.INSTALL REAR NO. 2 SEAT CUSHION HINGE UPPER COVER LH

a.
B564050C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and guide as shown in the illustration to install the rear No. 2 seat cushion hinge upper cover LH.


Hide 72552A 13.INSTALL RECLINING HINGE COVER LH

a.
B564046C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the clip and 4 claws as shown in the illustration to install the reclining hinge cover LH.


Hide 71834A 14.INSTALL REAR NO. 1 SEAT RECLINING COVER LH

a.
B564044C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and guide as shown in the illustration to install the rear No. 1 seat reclining cover LH.


Hide 71639 16.INSTALL REAR SEAT CUSHION HINGE COVER LH

a.
B564042C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 3 claws as shown in the illustration to install the rear seat cushion hinge cover LH.


Hide 71833A 17.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

a.
B564040C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and guide as shown in the illustration to install the rear No. 1 seat reclining cover RH.


Hide 71829B 18.INSTALL REAR SEAT CUSHION REAR MOULDING LH

a.
B569231C02
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 6 claws and 8 guides as shown in the illustration to install the rear seat cushion rear moulding LH.


Hide 72598C 19.INSTALL RECLINING REMOTE CONTROL BEZEL LH

a.
B564007

Engage the 2 claws and guide to install the reclining remote control bezel LH.


Hide 87510S 20.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71078S 21.INSTALL SEPARATE TYPE REAR SEATBACK COVER

HINT:

When installing a separate type rear seatback cover, refer to precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION


a.
B564036

Engage the 6 claws to install the separate type rear seatback cover to the separate type rear seatback pad LH.

NOTICE:

Be careful not to damage the separate type rear seatback cover.



Hide 22.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD

a.

Install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.


b.
B564034

Engage the hook.


c.
B564033C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws as shown in the illustration to install the 2 rear seat headrest supports.


Hide 71702C 23.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

a.
B566475C01
2.385,1.927 2.135,1.573 true 0.802,1.719 0.906,1.365 true 2.26,0.469 2.479,0.667 0.219,0.198 10 true *a 2.271,0.802 2.49,1 0.219,0.198 10 true *a 2.333,1.167 2.552,1.365 0.219,0.198 10 true *a 2.302,1.927 2.521,2.125 0.219,0.198 10 true *b 0.729,1.729 0.948,1.927 0.219,0.198 10 true *b
*a Clip
*b Cable


Engage the rear seat reclining control cable as shown in the illustration.

NOTICE:

Make sure to route the cable as shown in the illustration.



b.
B564031C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 2 guides as shown in the illustration.


c.
B564029

Engage the 6 clips and 2 claws as shown in the illustration to install the rear seatback board sub-assembly LH.


d.
B564027

Engage the hook.


e.
B564026C01
0,0 0,0 false
V100155

Fastener


Close the 2 fasteners as shown in the illustration.


Hide 72997 24.INSTALL REAR SEATBACK COVER LH

a.
B564024C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 6 claws as shown in the illustration to install the rear seatback cover LH.


b.
B564022

Engage the 2 claws as shown in the illustration.


Hide 72054C 25.INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH

a.
B564020

Connect the rear seat reclining control cable.


b.
B564019C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


c.
B564017

Install the reclining remote control lever sub-assembly LH with the 2 screws.


Hide 72616A 26.INSTALL REAR SEATBACK LOCK STRIKER COVER LH

a.
B564016C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and claw as shown in the illustration to install the rear seatback lock striker cover LH.


Hide 87501F 27.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

a.
B564003

Engage the clamp to install the seat heater control sub-assembly LH.


b.

Connect the connector.


Hide 87510Q 28.INSTALL SEAT HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71076S 29.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

HINT:

When installing a separate type rear seat cushion cover, refer to precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION


a.
B564010

Engage the 14 claws.

NOTICE:

Be careful not to damage the separate type rear seat cushion cover.



b.
B564008C02
0,0 0,0 false
V100155

Fastener


Engage the 5 fasteners to install the separate type rear seat cushion cover.


Hide 30.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

a.

Temporarily install the separate type rear seat cushion cover with pad to the No. 1 seat cushion frame sub-assembly LH.


b.
B564006

Engage the 6 hooks.


c.
B570464

Engage the hook.


d.
B564005

Engage the 2 hooks.


e.
B564004

w/ Seat Heater System:

i.

Engage the 2 clamps.


ii.

Connect the 2 connectors.



f.
B569681

Engage the clamp.


g.
B564002

Engage the 3 hooks.


h.
B564001

Engage the 2 hooks to install the separate type rear seat cushion cover with pad.


Hide 71826B 31.INSTALL REAR SEAT CUSHION MOULDING LH

a.
B564000C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 5 claws, clip and 14 guides as shown in the illustration to install the rear seat cushion moulding LH.


Hide 72058E 32.INSTALL REAR SEAT NO. 2 LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.
B563997

Connect the rear No. 1 seat track control cable assembly LH.


b.
B563996

Engage the 2 guides.


c.
B563995

Install the rear seat No. 2 lock control lever sub-assembly LH with the 2 screws.


Hide 72058D 33.INSTALL REAR SEAT NO. 1 LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.
B563992

Connect the rear seat reclining control cable.


b.
B563991

Engage the 2 guides.


c.
B563990

Install the rear seat No. 1 lock control lever sub-assembly LH with the 2 screws.


Hide 71849D 34.INSTALL SEAT ADJUSTER COVER CAP LH

a.
B563988

Engage the 2 guides and 2 claws to install the rear seat adjuster cover cap LH.


Hide 72928 35.INSTALL REAR SEAT CUSHION UNDER COVER LH

a.
B566425

Engage the claw, clip and guide to install the rear seat cushion under cover LH.


Hide 72526E 36.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.
B563987C03
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration to install the reclining adjuster release handle LH.


Hide 71848K 37.INSTALL SEAT ADJUSTER COVER CAP

a.
B566422

Install the 2 seat adjuster cover caps.