Wear protective gloves. Sharp areas on the seat frame may injure your hands.
72868B
1.REMOVE CENTER ARMREST HINGE COVER
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claw and 2 guides as shown in the illustration to remove the center armrest hinge cover.
72830
2.REMOVE REAR SEAT CENTER ARMREST ASSEMBLY
Remove the bolt and washer.
Disengage the guide as shown in the illustration to remove the rear seat center armrest assembly.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) | - | - |
72839
3.REMOVE REAR SEAT ARMREST HINGE SHIM
|
Remove in this Direction |
Remove the rear seat armrest hinge shim as shown in the illustration.
72806D
4.REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the 2 claws and 2 guides as shown in the illustration to remove the rear seat center armrest cup holder sub-assembly.
71848K
5.REMOVE SEAT ADJUSTER COVER CAP
Remove the 2 seat adjuster cover caps.
72525J
6.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration and remove the reclining adjuster release handle RH.
72927
7.REMOVE REAR SEAT CUSHION UNDER COVER RH
Disengage the claw, clip and guide to remove the rear seat cushion under cover RH.
71848C
8.REMOVE SEAT ADJUSTER COVER CAP RH
Disengage the 2 claws and 2 guides to remove the seat adjuster cover cap RH.
72057E
9.REMOVE REAR SEAT NO. 1 LOCK CONTROL LEVER SUB-ASSEMBLY RH
Remove the 2 screws.
Disengage the 2 guides.
Disconnect the rear seat reclining control cable to remove the rear seat No. 1 lock control lever sub-assembly RH.
72057F
10.REMOVE REAR SEAT NO. 2 LOCK CONTROL LEVER SUB-ASSEMBLY RH
Remove the 2 screws.
Disengage the 2 guides.
Disconnect the rear No. 1 seat track control cable assembly RH to remove the rear seat No. 2 lock control lever sub-assembly RH.
71825B
11.REMOVE REAR SEAT CUSHION MOULDING RH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the 5 claws, clip and 14 guides as shown in the illustration to remove the rear seat cushion moulding RH.
12.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
| *a | Rubber Band |
|
Remove in this Direction |
Remove the rear seat inner belt assembly from the rubber band of the separate type rear seat cushion cover as shown in the illustration.
Disengage the 4 hooks.
w/ Seat Heater System:
Disconnect the 2 connectors.
Disengage the 2 clamps.
| *a | Hook |
| *b | Clamp |
Disengage the 4 hooks and clamp.
|
Fastener |
Disengage the fastener and 7 hooks.
Disengage the 6 hooks and remove the separate type rear seat cushion cover with pad.
71075S
13.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
|
Fastener |
Disengage the 7 fasteners.
Using a screwdriver, disengage the 14 claws as shown in the illustration and remove the bench type rear seat cushion cover from the rear seat cushion pad RH.
| *a | Screwdriver | - | - |
87510P
14.REMOVE SEAT HEATER ASSEMBLY (w/ Seat Heater System)
87501E
15.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)
Disconnect the connector.
Disengage the clamp to remove the seat heater control sub-assembly RH.
71485
16.REMOVE REAR SEAT HINGE COVER
|
Remove in this Direction |
Using a moulding remover, disengage the clip and 3 claws as shown in the illustration to remove the rear seat hinge cover.
73380X
17.REMOVE REAR SEAT INNER BELT ASSEMBLY RH
71828B
18.REMOVE REAR SEAT CUSHION REAR MOULDING RH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the 6 claws, clip and 6 guides as shown in the illustration to remove the rear seat cushion rear moulding RH.
73380A
19.REMOVE REAR SEAT INNER BELT ASSEMBLY
72615A
20.REMOVE REAR SEATBACK LOCK STRIKER COVER RH
|
Remove in this Direction |
Disengage the claw and 2 guides as shown in the illustration to remove the rear seatback lock striker cover RH.
72053E
21.REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH
Remove the 2 screws.
|
Remove in this Direction |
Disengage the guide as shown in the illustration.
Disconnect the rear seat reclining control cable to remove the reclining remote control lever sub-assembly RH.
72996
22.REMOVE REAR SEATBACK COVER RH
Disengage the 2 claws as shown in the illustration.
Use the same procedure for each rear seatback cover RH.
|
Remove in this Direction |
Disengage the 6 claws as shown in the illustration to remove the rear seatback cover RH.
Use the same procedure for each rear seatback cover RH.
73350
23.DISCONNECT REAR NO. 1 SEAT CENTER LAP TYPE BELT ASSEMBLY
73373
24.REMOVE REAR SEAT SHOULDER BELT COVER
Disengage the 2 claws and 2 guides to remove the rear seat shoulder belt cover.
73178A
25.REMOVE SEAT BELT ANCHOR COVER CAP
|
Remove in this Direction |
Disengage the 2 guides as shown in the illustration to remove the seat belt anchor cover cap.
71701B
26.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH
|
Fastener |
Open the 2 fasteners as shown in the illustration.
Disengage the 2 hooks.
Disengage the 9 clips and 4 claws as shown in the illustration.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the 4 guides as shown in the illustration to remove the rear seatback board sub-assembly RH.
27.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
|
Remove in this Direction |
Disengage the 4 claws as shown in the illustration to remove the 2 rear seat headrest supports.
Use the same procedure for each rear seat headrest support.
|
Fastener |
Disengage the fastener and 3 hooks and remove the separate type rear seatback cover with pad.
71077S
28.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Using a screwdriver, disengage the 6 claws as shown in the illustration and remove the separate type rear seatback cover from the separate type rear seatback pad.
| *a | Screwdriver | - | - |
87510R
29.REMOVE SEAT HEATER ASSEMBLY (w/ Seat Heater System)
72597D
30.REMOVE RECLINING REMOTE CONTROL BEZEL RH
Disengage the 2 claws and guide to remove the reclining remote control bezel RH.
73350
31.REMOVE REAR NO. 1 SEAT CENTER LAP TYPE BELT ASSEMBLY
71629A
32.REMOVE REAR SEAT CUSHION HINGE COVER RH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the 2 guides as shown in the illustration to remove the rear seat cushion hinge cover RH.
71486C
33.REMOVE REAR SEAT HINGE COVER LH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the 5 claws and 6 guides as shown in the illustration to remove the rear seat hinge cover LH.
71834A
34.REMOVE REAR NO. 1 SEAT RECLINING COVER LH
|
Remove in this Direction |
Disengage the claw and guide as shown in the illustration to remove the rear No. 1 seat reclining cover LH.
71485
35.REMOVE REAR SEAT HINGE COVER
|
Remove in this Direction |
Disengage the 3 claws as shown in the illustration to remove the rear seat hinge cover.
71833A
36.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
|
Remove in this Direction |
Disengage the claw and guide as shown in the illustration to remove the rear No. 1 seat reclining cover RH.
72551E
37.REMOVE RECLINING HINGE COVER RH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the 4 claws and clip as shown in the illustration to remove the reclining hinge cover RH.
71693
38.REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH
|
Remove in this Direction |
Disengage the claw and 2 guides as shown in the illustration to remove the rear seat cushion hinge lower cover RH.
71691N
39.REMOVE REAR NO. 1 SEAT CUSHION HINGE UPPER COVER RH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claw and guide as shown in the illustration to remove the rear No. 1 seat cushion hinge upper cover RH.
82193
40.REMOVE REAR SEAT WIRE RH (w/o Seat Heater System)
Disengage the 10 clamps and remove the rear seat wire RH.
82193
41.REMOVE REAR SEAT WIRE RH (w/ Seat Heater System)
w/o Seat Belt Warning System:
Disengage the 7 clamps and remove the rear seat wire RH.
w/ Seat Belt Warning System:
Disengage the 11 clamps and remove the rear seat wire RH.
42.REMOVE CONNECTOR MALE HOUSING (w/o Seat Heater System)
w/o Seat Belt Warning System:
Disengage the clamp to remove the connector male housing.
72210G
43.REMOVE REAR NO. 1 SEAT TRACK CONTROL CABLE ASSEMBLY RH
Remove the 2 wire harness clamps.
|
Clamp |
|
Wire Harness Clamp |
Disengage the 2 clamps and remove the rear No. 1 seat track control cable assembly RH.
72704A
44.REMOVE REAR SEAT RECLINING CONTROL CABLE
Disengage the 12 clamps.
Disengage the clamp and remove the rear seat reclining control cable.
72307D
45.REMOVE NO. 1 RECLINING CONTROL LINK SUB-ASSEMBLY RH
Remove the 2 nuts and No. 1 reclining control link sub-assembly RH.
72307E
46.REMOVE NO. 2 RECLINING CONTROL LINK SUB-ASSEMBLY RH
Remove the 2 nuts and No. 2 reclining control link sub-assembly RH.
71017
47.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH
Using a T55 "TORX" socket wrench, remove the 2 bolts (A).
|
Bolt (A) |
|
Bolt (B) |
|
Remove in this Direction | - | - |
Remove the 3 bolts (B).
Remove the rear seatback frame sub-assembly RH from the No. 1 seat cushion frame sub-assembly RH as shown in the illustration.
71015A
48.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH
Remove the 6 nuts and rear seat cushion frame sub-assembly RH.