Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SENSOR
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0417855 BLIND SPOT MONITOR SENSOR N

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SENSOR  ADJUSTMENT  


PROCEDURE

Hide 1.PERFORM BLIND SPOT MONITOR BEAM AXIS CONFIRMATION

HINT:

The blind spot monitor beam axis confirmation is performed to confirm whether the sensor beam axis is correct, and to adjust the beam axis by using a reflector.


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

E305141C05
0.927,0.354 1.24,0.51 0.313,0.156 12 false *A 3.854,0.375 4.167,0.531 0.313,0.156 12 false *B 2.688,0.51 3,0.667 0.313,0.156 10 false *a 3.042,1.885 3.354,2.042 0.313,0.156 10 false *b 1.365,4.406 1.677,4.563 0.313,0.156 10 false *c 4.292,0.5 4.604,0.656 0.313,0.156 10 false *a 4.021,1.885 4.333,2.042 0.313,0.156 10 false *b 0.802,1.74 1.115,1.896 0.313,0.156 10 false a 6.24,1.719 6.573,1.885 0.333,0.167 10 false a 6.26,2.521 6.573,2.688 0.313,0.167 10 false b 0.719,2.521 1.031,2.688 0.313,0.167 10 false b 1.865,3.604 2.177,3.76 0.313,0.156 10 false c 5.052,3.563 5.365,3.719 0.313,0.156 10 false c
*A Left Side of Vehicle *B Right Side of Vehicle
*a Vehicle Center Line *b Rear Bumper
*c Inspection Area - -


Standard:
Location Measurement
a 1 m (3.28 ft.)
b 5 m (16.41 ft.)
c 6 m (19.68 ft.)


NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place any objects other than the reflector (such as a large metallic object) in the inspection area or allow people to enter the inspection area (W 6 m [19.68 ft.] x L 6 m [19.68 ft.] x H 4 m [13.12 ft.]) shown in the illustration.




b.

Place the reflector.

i.

Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the vehicle (point A) on the ground.

E432183C01
5,1.292 5.563,1.292 true 5.583,1.979 5.917,1.979 true 2.802,2.458 3.104,2.521 false 2.813,2.365 3.313,2.26 false 5.927,1.896 6.24,2.052 0.313,0.156 10 false *a 3.333,2.167 3.646,2.323 0.313,0.156 10 false *b 4.844,1.208 5.156,1.365 0.313,0.156 10 false *c 3.156,2.448 3.313,2.646 0.156,0.198 10 false A
*a String *b Weight
*c Center - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark A.



ii.

Hang a weight with a pointed tip from the center of the radiator grille (or front panel) emblem, and mark the front center point of the vehicle (point B) on the ground.

E432184C01
3.719,2.24 4.063,2.156 false 3.49,1.979 4.052,2.073 false 1.583,1.958 2.115,1.844 true 0.979,1.25 1.583,1.25 true 2.135,1.75 2.385,1.927 0.25,0.177 10 true *a 3.333,1.896 3.646,2.052 0.313,0.156 10 false *b 0.802,1.156 1.01,1.344 0.208,0.188 10 true *c 3.594,2.177 3.75,2.375 0.156,0.198 10 false B
*a String *b Weight
*c Center - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark B.



iii.
E238824C10
0.927,1.271 0.677,0.771 0.677,0.771 0.51,0.771 false 1.292,1.302 1.448,1.458 0.156,0.156 10 false A 3.052,1.302 3.208,1.458 0.156,0.156 10 false B 0.344,0.677 0.656,0.875 0.313,0.198 10 false *a
*a Vehicle Center Line


Draw a vehicle center line so that it passes through mark A and B (front and rear center points).


iv.

Enlarge and print out the poster shown in the illustration.

E432255C01
5.156,4.01 4.99,4.01 4.99,4.01 4.813,4.417 false 3.458,5.479 3.292,5.479 3.292,5.479 3.021,5.802 false 3.531,3.313 3.365,3.313 3.365,3.313 3.073,2.969 false 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 2.031,4.542 2.344,4.74 0.313,0.198 10 false A 1.208,4.021 1.521,4.219 0.313,0.198 10 false *b 2.792,3.979 3.104,4.177 0.313,0.198 10 false a 2.781,4.708 3.094,4.906 0.313,0.198 10 false a 5.188,3.917 5.5,4.115 0.313,0.198 10 false *d 3.552,3.208 3.865,3.406 0.313,0.198 10 false *c 3.49,5.385 3.802,5.583 0.313,0.198 10 false *c
*a Poster *b Edge of Rear Bumper
*c Line C *d Vehicle Center Line


Standard:
Part Angle
a 55.5°



v.
E334361C13
0.833,1.542 1.104,1.542 1.104,1.542 1.802,1.948 true 1.833,2.906 2.354,2.906 false 2.479,2.51 2.313,2.51 2.313,2.51 2.01,2.177 false 0.688,1.458 0.844,1.656 0.156,0.198 10 false A 2.385,2.823 2.698,3.021 0.313,0.198 10 false *b 2.51,2.417 2.823,2.615 0.313,0.198 10 false *a
*a Poster
*b Vehicle Center Line


Attach the printed poster to the floor with the vehicle center line aligned with point A as shown in the illustration.


vi.
E334362C13
2.146,3.729 1.938,3.729 1.938,3.729 1.813,3.396 false 2.771,3.292 2.469,3.292 2.469,3.292 2.333,3.542 false 2.792,2.448 2.344,2.448 2.344,2.448 1.729,3.167 true 0.583,3.729 0.74,3.927 0.156,0.198 10 false D 2.771,3.708 2.927,3.906 0.156,0.198 10 false D 0.26,0.333 0.573,0.51 0.313,0.177 10 false *a 1.625,4.354 1.938,4.531 0.313,0.177 10 false *b 2.156,3.635 2.469,3.813 0.313,0.177 10 false *d 2.813,3.198 3.125,3.375 0.313,0.177 10 false *c 2.875,2.354 3.031,2.552 0.156,0.198 10 false A
*a Vehicle Front
*b Vehicle Center Line
*c String
*d Poster


Align a piece of string with line C and mark point D at a distance of 2941 mm (9.65 ft.) from point A.


vii.

Set the reflector at the point D shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E334360C15
1.208,2.906 0.885,2.552 0.885,2.552 0.719,2.552 false 5.969,2.885 6.313,2.552 6.313,2.552 6.479,2.552 false 2.406,2.24 2.76,2.427 false 4.365,2.438 4.74,2.26 false 1.521,0.583 1.854,0.823 0.333,0.24 12 false *A 3.948,0.583 4.26,0.896 0.313,0.313 12 false *B 2.333,3.24 2.646,3.396 0.313,0.156 10 false *a 0.552,2.458 0.865,2.615 0.313,0.156 10 false *b 4.667,3.188 4.979,3.344 0.313,0.156 10 false *a 1.74,2.385 2.177,2.573 0.438,0.188 10 false a 5.396,2.385 5.833,2.573 0.438,0.188 10 false a 1.021,2.99 1.365,3.177 0.344,0.188 10 false D 6.063,2.958 6.406,3.146 0.344,0.188 10 false D 6.521,2.469 6.833,2.625 0.313,0.156 10 false *b 2.813,2.375 2.969,2.573 0.156,0.198 10 false A 4.229,2.375 4.385,2.573 0.156,0.198 10 false A
*A Left Side of Vehicle *B Right Side of Vehicle
*a Vehicle Center Line *b Reflector


Standard:
Part Length
a 2941 mm (9.65 ft.)


NOTICE:
·
E238830C08
1.469,0.667 1.979,0.667 1.979,0.667 1.625,1.177 false 2.031,0.594 2.344,0.792 0.313,0.198 10 false *a 0.604,1.563 0.917,1.76 0.313,0.198 10 false *b
*a SST (reflector)
*b 752 mm (2.47 ft.)


Set the reflector so that its center is 752 mm (2.47 ft.) above the ground.

·
E338853C05
2.125,0.719 2.396,1.438 true 2.417,1.5 2.74,1.729 0.323,0.229 10 false *a
*a Center of Triangular Pyramid


The center of the triangular pyramid is the reference point for the setting position and angle.

·

Set the reflector as shown in the illustration so that the center of the triangular pyramid faces the blind spot monitor sensor.





c.

Perform the blind spot monitor beam axis display.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the blind spot monitor system on.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Display or BSM Slave Beam Axis Display.

HINT:

The master beam is on the LH side and the slave beam is on the RH side.

Part Name Tester Item Expression in Others
Blind spot monitor sensor LH Blind Spot Monitor Master Blind spot monitor sensor LH (B)
Blind spot monitor sensor RH Blind Spot Monitor Slave Blind spot monitor sensor RH (A)


Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Display
50005 313 4238
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Display
50005 314 4239

vi.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor LH Blind Spot Monitor Sensor RH
Angle -3.6 to +3.6° -3.6 to +3.6°


HINT:

If the displayed results are outside the permissible range, the following are possible causes. Therefore, implement countermeasures, check the blind spot monitor beam axis and perform the procedure again.

Possible Causes Countermeasure
Incorrect SST (reflector) position Check the position of SST (reflector) and checking space and perform the procedure again
A metallic object is located in the vicinity of the checking space Check the position of SST (reflector) and checking space and perform the procedure again
The blind spot monitor sensor installation is abnormal Check the installation condition of the blind spot monitor sensor




d.

Perform the blind spot monitor beam axis adjustment.

i.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Adjustment or BSM Slave Beam Axis Adjustment.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Adjustment
50005 313 4231
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Adjustment
50005 314 4232
HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates for any deviation from the normal value.




Hide 2.PERFORM BLIND SPOT MONITOR SENSOR INSTALLATION CONDITION INSPECTION

NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



HINT:

The blind spot monitor sensor installation condition inspection is performed to confirm whether the sensor is perpendicular to the floor surface (+/-2.2°) by using a digital angle gauge, and that the sensor is 46 to 54° from the line parallel to the vehicle center line.


a.

Remove the rear bumper assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER>REMOVAL


b.

Place the digital angle gauge on a level (gradient within 1%) and perform zero-point adjustment as shown in the illustration.

E369196C14
0.958,1.063 1.125,1.063 1.125,1.063 1.708,1.396 true 0.958,1.781 1.125,1.781 1.125,1.781 1.708,1.531 true 5.75,0.5 5.583,0.5 5.583,0.5 5.292,1.042 true 4.708,0.49 4.875,0.49 4.875,0.49 5.146,1.042 true 1.969,2.396 2.146,2.604 0.177,0.208 10 false *c 5.073,2.135 5.313,2.344 0.24,0.208 10 false *d 0.771,0.958 1.229,1.156 0.458,0.198 10 false *a 0.792,1.688 1.25,1.885 0.458,0.198 10 false *b 4.531,0.396 4.99,0.594 0.458,0.198 10 false *b 5.802,0.406 6.26,0.604 0.458,0.198 10 false *a
*a (+) *b (-)
*c When Storing Zero Point *d After Storing Zero Point, Indicates 90° When Fully Horizontal



c.
E432185C01
0.563,1.677 1.104,1.677 true 2.177,1.885 2.781,1.885 true 1.323,2.719 1.604,2.146 true 0.406,1.583 0.719,1.74 0.313,0.156 10 false *1 2.792,1.792 3.052,2 0.26,0.208 10 true *a 1.219,2.719 1.469,2.906 0.25,0.188 10 false *b
*1 Blind Spot Monitor Sensor
*a Digital Angle Gauge
*b Outward Facing Surface


Set the digital angle gauge to the outward facing surface of the blind spot monitor sensor as shown in the illustration, and check that the perpendicular angle of the blind spot monitor sensor is within the permissible range.

NOTICE:
E367769C12
2.479,1.229 2.667,1.01 2.667,1.01 2.833,1.01 false 1.313,0.74 1.573,0.333 1.573,0.333 1.729,0.333 false 0.573,1.813 0.698,1.813 0.698,1.813 0.938,1.583 true 2.24,0.771 2.625,0.969 0.385,0.198 10 false *a 2.26,1.531 2.646,1.729 0.385,0.198 10 false *b 2.865,0.927 3.156,1.125 0.292,0.198 10 false *c 1.76,0.25 2.135,0.469 0.375,0.219 10 false *d 0.396,1.729 0.781,1.99 0.385,0.26 10 false *e
*a (+)
*b (-)
*c Horizontal Line
*d Digital Angle Gauge
*e Outward Facing Surface


The sensor angle is the measured sensor angle subtracted from 90°.


HINT:
·

The digital angle gauge should indicate 90° when turned on its side.

·

The outward facing surface (installation angle) is positive (+) when it faces higher than horizontal.



Standard:
Item Allowable Range
Blind Spot Monitor Sensor LH +2.2 to -2.2°
Blind Spot Monitor Sensor RH +2.2 to -2.2°



d.
E359641C07
0.208,2.323 0.344,2.323 0.344,2.323 0.5,2.458 false 1.854,3.167 2.063,3.333 2.063,3.333 2.198,3.333 false 1.583,3.375 1.75,3.563 1.75,3.563 1.885,3.563 false 0.76,2.271 0.969,2.438 0.969,2.438 1.104,2.438 false 0.094,0.083 0.406,0.323 0.313,0.24 12 false *A 1.635,2.083 1.823,2.26 0.188,0.177 10 true a 1.802,4.125 2.115,4.281 0.313,0.156 10 false *b 1.125,2.365 1.438,2.521 0.313,0.156 10 false *d 0.052,2.24 0.365,2.396 0.313,0.156 10 false *e 1.104,3.26 1.365,3.49 0.26,0.229 10 false y 0.438,1.365 0.75,1.521 0.313,0.156 10 false A 1.802,0.521 2.073,0.708 0.271,0.188 10 false *a 0.542,0.667 0.854,0.823 0.313,0.156 10 false *f 3.104,0.656 3.354,0.833 0.25,0.177 10 false *c 1.917,3.479 2.208,3.656 0.292,0.177 10 false *e 2.24,3.25 2.552,3.406 0.313,0.156 10 false *d
*A Vehicle Rear (LH)
*a Vehicle Front
*b Vehicle Rear
*c Vehicle Center Line
*d Stud Bolt
*e Stud Bolt Center Line
*f Line Parallel to Vehicle Center Line


Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
a 108 mm (4.25 in.)
y 78 to 87 mm
(3.07 to 3.43 in.)

Degree Specified Value
A 46 to 54°


HINT:

If the results are not as specified, it is possible that the blind spot monitor sensor installation area (frame, stud bolt) is deformed, so make corrections as necessary.