Home › Steering › STEERING COLUMN › STEERING SYSTEM
RM37A0E _55 Steering _086875 STEERING COLUMN _0418167 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING WHEEL OFF CENTER ADJUSTMENT PROCEDURE

a.

Inspect steering wheel off center.

i.

Turn the steering wheel assembly to the center position.


ii.
C425013C01
1.063,0.427 1.719,0.427 false 1,1.052 1.656,1.052 false 1.896,0.948 0.938,0.635 0.938,0.635 2,0.802 true 0.906,0.344 1.219,0.5 0.313,0.156 10 false *1 0.844,0.979 1.156,1.135 0.313,0.156 10 false *2 0.771,0.542 1.083,0.698 0.313,0.156 10 false *a
*1 Steering Wheel Assembly
*2 Upper Steering Column Cover
*a Masking Tape


Apply masking tape to the top center of the steering wheel assembly and upper steering column cover.


iii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), while holding the steering wheel assembly to maintain the course.


iv.
C425014C01
0.927,0.448 1.688,0.448 false 0.917,0.969 1.677,0.969 false 2.198,0.896 1.125,0.729 1.125,0.729 2.198,0.656 true 0.76,0.375 1.073,0.531 0.313,0.156 10 false *1 0.771,0.896 1.083,1.052 0.313,0.156 10 false *2 0.958,0.646 1.271,0.802 0.313,0.156 10 false *a
*1 Upper Steering Column Cover
*2 Steering Wheel Assembly
*a Marked Line


Draw a line on the masking tape as shown in the illustration.


v.

Turn the steering wheel assembly to the center position.


vi.
C425015C01
1.688,0.344 0.927,0.344 false 1.667,0.958 0.906,0.958 false 2.198,0.833 1.135,0.635 1.135,0.635 2.208,0.594 true 0.76,0.271 1.073,0.427 0.313,0.156 10 false *1 0.75,0.875 1.063,1.031 0.313,0.156 10 false *2 0.958,0.542 1.271,0.698 0.313,0.156 10 false *a
*1 Upper Steering Column Cover
*2 Steering Wheel Assembly
*a Marked Line


Draw a new line on the masking tape on the steering wheel assembly as shown in the illustration.


vii.

Measure the distance between the 2 lines on the masking tape on the steering wheel assembly.


viii.

Convert the measured distance to the steering angle.

HINT:
·

Measured distance of 1 mm (0.0394 in.) = Steering angle of approximately 1 degree

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C425016C01
1.74,1.271 1.521,1.615 1.521,1.615 1.802,1.292 true 1.448,1.615 1.76,1.771 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the tie rod assemblies LH and RH and steering rack end sub-assembly respectively.


ii.

Using a paper gauge, measure the thread length of the steering rack end sub-assemblies.

HINT:
·

Measure both RH and LH sides.

·

Make a note of the measured values.




iii.
C425017

Remove the steering rack boot clips from the RH and LH steering rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH steering rack end sub-assemblies by the same amount (but in different directions) according to the measured steering angle.

HINT:

One 360 degree turn of a steering rack end sub-assembly (1.5 mm (0.0591 in.) horizontal movement) equals 9.6 degrees of steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>INSTALLATION

NOTICE:

Make sure that the difference in thread length between the RH and LH steering rack end sub-assemblies is within 1.5 mm (0.0591 in.).



vii.

Install the RH and LH steering rack boot clips.

Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>REASSEMBLY