Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0418174 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1642  Side Satellite Sensor Bus Lost Communication (RH)  B1643  Side Satellite Sensor Bus Initialization Error (RH)  


DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH.

The side airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1642 Side Satellite Sensor Bus Lost Communication (RH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

·

Rear airbag sensor RH malfunction

·

Side airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Rear airbag sensor RH

·

Side airbag sensor assembly RH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode
B1643 Side Satellite Sensor Bus Initialization Error (RH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

·

Rear airbag sensor RH malfunction

·

Side airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Rear airbag sensor RH

·

Side airbag sensor assembly RH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B473433E86
4.594,1.99 6.26,2.354 1.667,0.365 10 false Airbag Sensor Assembly 4.594,1.823 6.26,2.188 1.667,0.365 10 false M10 5.219,0.948 5.844,1.271 0.625,0.323 10 false Interface 1.656,2.531 2.281,2.854 0.625,0.323 10 false Interface 4.927,3.229 6.51,3.573 1.583,0.344 10 false Interface 0.771,2.542 1.406,2.833 0.635,0.292 10 false Element 5.865,3.229 6.5,3.521 0.635,0.292 10 false Element 4.646,0.51 6.313,0.875 1.667,0.365 10 false BBR+ 4.646,1.177 6.313,1.542 1.667,0.365 10 false BBR- 4.396,0.51 4.979,0.875 0.583,0.365 10 false 25 4.396,1.177 6.063,1.542 1.667,0.365 10 false 26 2.396,1.427 4.063,1.792 1.667,0.365 10 false BCR+ 2.854,1.427 4.521,1.792 1.667,0.365 10 false 4 2.417,2.094 4.083,2.458 1.667,0.365 10 false BCR- 2.854,2.094 4.521,2.458 1.667,0.365 10 false 3 2.406,2.781 4.073,3.146 1.667,0.365 10 false BDR+ 2.844,2.781 4.51,3.146 1.667,0.365 10 false 1 2.417,3.458 4.083,3.823 1.667,0.365 10 false BDR- 2.844,3.469 4.51,3.833 1.667,0.365 10 false 2 3.438,2.885 5.104,3.25 1.667,0.365 10 false JM1 3.521,2.688 5.188,3.052 1.667,0.365 10 false 1 3.521,3.375 5.188,3.74 1.667,0.365 10 false 2 4.208,2.781 5.875,3.146 1.667,0.365 10 false 2 4.208,3.458 5.875,3.823 1.667,0.365 10 false 1 4.375,2.781 6.042,3.146 1.667,0.365 10 false BDR+ 4.375,3.458 6.042,3.823 1.667,0.365 10 false BDR- 0.563,4.125 2.229,4.49 1.667,0.365 10 false M11 0.563,4.292 3.344,4.573 2.781,0.281 10 false Rear Airbag Sensor RH 4.333,4.125 6,4.49 1.667,0.365 10 false J11 4.333,4.302 6.667,4.542 2.333,0.24 10 false Side Airbag Sensor Assembly RH 3.448,3.563 5.115,3.927 1.667,0.365 10 false JM1

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

3.CHECK FLOOR WIRE
a.
B474702C28
0.823,0.844 1.188,1.063 0.365,0.219 0.833,3.792 1.198,4.01 0.365,0.219 1.271,1.719 1.635,1.292 false 2.094,1.719 1.74,1.292 false 1.698,1.823 1.698,1.677 false 1.625,2.854 1.625,2.375 1.625,2.375 1.458,2.375 false 1.677,4.198 1.948,3.865 false 2.281,4.198 2.063,3.865 false 0.76,2.844 1.219,3.344 0.458,0.5 10 false *1 2.521,2.573 3.031,2.948 0.51,0.375 10 false *2 1.313,2.292 1.844,2.833 0.531,0.542 10 false *3 1.635,1.823 2.115,2.24 0.479,0.417 10 false *4 0.656,0.177 1.156,0.677 0.5,0.5 10 false *a 0.698,3.417 1.156,3.792 0.458,0.375 10 false *b 2.188,2.844 2.698,3.219 0.51,0.375 10 false A 1.885,2.844 2.396,3.219 0.51,0.375 10 false B 1.292,2.844 1.802,3.219 0.51,0.375 10 false C 0.979,2.844 1.49,3.219 0.51,0.375 10 false D 1.115,1.729 1.573,2.229 0.458,0.5 10 false BBR+ 0.896,3.823 1.354,4.323 0.458,0.5 10 false M11 1.969,1.729 2.427,2.229 0.458,0.5 10 false BBR- 0.885,0.875 1.344,1.375 0.458,0.5 10 false M10 2.135,4.219 2.646,4.469 0.51,0.25 10 false BCR+ 1.531,4.219 2.042,4.469 0.51,0.25 10 false BCR-
*1 Rear Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M11-4 (BCR+) - Body ground Ignition switch ON Below 1 V
M11-3 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-4 (BCR+) - M11-3 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-4 (BCR+) - M11-3 (BCR-) Always 1 MΩ or higher
M11-4 (BCR+) - Body ground Always 1 MΩ or higher
M11-3 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS

NG

REPLACE FLOOR WIRE

4.CHECK WIRE HARNESS
a.
C295812C54
0.521,3.615 0.885,3.865 0.365,0.25 0.833,0.656 1.25,0.906 0.417,0.25 0.948,4.146 1.375,3.771 false 2.052,4.167 1.656,3.76 false 1.531,4.385 1.531,4.219 false 1.448,1.24 1.76,0.781 false 2.219,1.24 1.938,0.781 false 1.448,2.344 1.448,1.906 1.448,1.906 1.24,1.906 false 1.958,2.771 1.958,2.469 false 0.552,2.333 1.042,2.781 0.49,0.448 10 false *1 2.719,2.333 3.208,2.802 0.49,0.469 10 false *2 1.469,4.385 1.854,4.667 0.385,0.281 10 false *5 0.635,0.177 1.073,0.656 0.438,0.479 10 false *a 0.354,3.167 0.792,3.813 0.438,0.646 10 false *b 2.385,2.333 2.875,2.802 0.49,0.469 10 false A 2.083,2.333 2.573,2.802 0.49,0.469 10 false B 1.74,2.333 2.229,2.802 0.49,0.469 10 false C 1.583,2.333 2.073,2.802 0.49,0.469 10 false D 1.229,2.333 1.719,2.802 0.49,0.469 10 false E 0.927,2.333 1.417,2.802 0.49,0.469 10 false F 1.302,1.25 1.844,1.521 0.542,0.271 10 false BDR+ 2.083,1.25 2.75,1.667 0.667,0.417 10 false BDR- 1.906,4.167 2.406,4.635 0.5,0.469 10 false BDR+ 0.792,4.167 1.292,4.5 0.5,0.333 10 false BDR- 0.927,0.698 1.469,0.969 0.542,0.271 10 false M11 0.615,3.656 1.156,3.927 0.542,0.271 10 false J11 1.083,1.833 1.469,2.115 0.385,0.281 10 false *3 1.896,2.792 2.281,3.073 0.385,0.281 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M11-1 (BDR+) - Body ground Ignition switch ON Below 1 V
M11-2 (BDR-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-1 (BDR+) - M11-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-1 (BDR+) - M11-2 (BDR-) Always 1 MΩ or higher
M11-1 (BDR+) - Body ground Always 1 MΩ or higher
M11-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK REAR AIRBAG SENSOR RH

NG

7.CHECK FLOOR WIRE
5.CHECK REAR AIRBAG SENSOR RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Rear Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connectors to the side airbag sensor assembly RH and airbag sensor assembly.


b.

Interchange the rear airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647 and B1648 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642 or B1643 is output. A
DTC B1647 or B1648 is output. B
DTCs B1642, B1643, B1647 and B1648 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.



A

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

B

C

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Side Airbag Sensor Assembly LH
*2 Rear Airbag Sensor RH


Interchange the side airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647 and B1648 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642 or B1643 is output. A
DTC B1647 or B1648 is output. B
DTCs B1642, B1643, B1647 and B1648 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

7.CHECK FLOOR WIRE
a.
B566952C01
0.823,0.802 1.208,1.052 0.385,0.25 1.073,3.563 1.469,3.781 0.396,0.219 1.844,1.531 1.844,1.333 false 1.333,1.406 1.771,0.906 false 2.333,1.406 1.917,0.906 false 1.333,2.469 1.333,2.719 false 1.906,2 2.073,2 2.073,2 2.073,2.333 false 1.51,3.417 1.833,3.479 false 2.375,3.427 2.031,3.479 false 0.406,2.323 0.802,2.729 0.396,0.406 10 false *1 2.865,2.323 3.26,2.896 0.396,0.573 10 false *2 1.271,2.729 1.604,2.969 0.333,0.24 10 false *3 1.75,1.927 2.146,2.26 0.396,0.333 10 false *4 1.781,1.542 2.198,1.865 0.417,0.323 10 false *5 0.635,0.406 1.031,0.823 0.396,0.417 10 false *a 1.01,3.146 1.406,3.552 0.396,0.406 10 false *b 2.542,2.323 2.938,2.896 0.396,0.573 10 false A 2.24,2.323 2.635,2.896 0.396,0.573 10 false B 1.813,2.323 2.208,2.896 0.396,0.573 10 false C 1.521,2.313 1.917,2.885 0.396,0.573 10 false D 1.094,2.323 1.49,2.896 0.396,0.573 10 false E 0.792,2.323 1.188,2.896 0.396,0.573 10 false F 1.177,1.417 1.677,1.75 0.5,0.333 10 false BDR+ 2.198,1.417 2.698,1.75 0.5,0.333 10 false BDR- 2.427,3.344 2.896,3.646 0.469,0.302 10 false BDR+ 1.135,3.333 1.635,3.667 0.5,0.333 10 false BDR- 0.896,0.844 1.396,1.177 0.5,0.333 10 false M11 1.135,3.583 1.635,3.917 0.5,0.333 10 false JM1
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
JM1-1 (BDR+) - Body ground Ignition switch ON Below 1 V
JM1-2 (BDR-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-1 (BDR+) - JM1-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-1 (BDR+) - JM1-2 (BDR-) Always 1 MΩ or higher
JM1-1 (BDR+) - Body ground Always 1 MΩ or higher
JM1-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE