The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH.
The side airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B166D | Lost Communication with Front Door Pressure Sensor RH | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Rear airbag sensor RH malfunction ·
Side airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Rear airbag sensor RH ·
Side airbag sensor assembly RH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
| B166E | Front Door Pressure Sensor RH Initialization Incomplete | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Rear airbag sensor RH malfunction ·
Side airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Rear airbag sensor RH ·
Side airbag sensor assembly RH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the side airbag sensor assembly RH and rear airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the side airbag sensor assembly RH and rear airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the connectors that link the floor wire and front door wire RH.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M11-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| M11-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M11-1 (BDR+) - M11-2 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M11-1 (BDR+) - M11-2 (BDR-) | Always | 1 MΩ or higher |
| M11-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| M11-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the side airbag sensor assembly RH.
Interchange the rear airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B166D or B166E is output. | A |
| DTC B167B or B167C is output. | B |
| DTCs B166D, B166E, B167B and B167C are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Rear Airbag Sensor RH |
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B166D or B166E is output. | A |
| DTC B167B or B167C is output. | B |
| DTCs B166D, B166E, B167B and B167C are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| JM1-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| JM1-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| JM1-1 (BDR+) - JM1-2 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| JM1-1 (BDR+) - JM1-2 (BDR-) | Always | 1 MΩ or higher |
| JM1-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| JM1-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG