Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0418174 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B167B  Lost Communication with Front Door Pressure Sensor LH  B167C  Front Door Pressure Sensor LH Initialization Incomplete  


DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.

The side airbag sensor assembly LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B167B Lost Communication with Front Door Pressure Sensor LH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Rear airbag sensor LH malfunction

·

Side airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 floor wire

·

Front door wire LH

·

Rear airbag sensor LH

·

Side airbag sensor assembly LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode
B167C Front Door Pressure Sensor LH Initialization Incomplete
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Rear airbag sensor LH malfunction

·

Side airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 floor wire

·

Front door wire LH

·

Rear airbag sensor LH

·

Side airbag sensor assembly LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B473433E87
4.594,1.99 6.26,2.354 1.667,0.365 10 false Airbag Sensor Assembly 4.594,1.823 6.26,2.188 1.667,0.365 10 false M61 5.219,0.948 5.844,1.271 0.625,0.323 10 false Interface 1.656,2.531 2.281,2.854 0.625,0.323 10 false Interface 4.927,3.229 6.51,3.573 1.583,0.344 10 false Interface 0.771,2.542 1.406,2.833 0.635,0.292 10 false Element 5.865,3.229 6.5,3.521 0.635,0.292 10 false Element 4.646,0.51 6.313,0.875 1.667,0.365 10 false BBL+ 4.646,1.177 6.313,1.542 1.667,0.365 10 false BBL- 4.396,0.51 4.979,0.875 0.583,0.365 10 false 32 4.396,1.177 6.063,1.542 1.667,0.365 10 false 31 2.396,1.427 4.063,1.792 1.667,0.365 10 false BCL+ 2.854,1.427 4.521,1.792 1.667,0.365 10 false 4 2.417,2.094 4.083,2.458 1.667,0.365 10 false BCL- 2.854,2.094 4.521,2.458 1.667,0.365 10 false 3 2.406,2.781 4.073,3.146 1.667,0.365 10 false BDL+ 2.844,2.781 4.51,3.146 1.667,0.365 10 false 1 2.417,3.458 4.083,3.823 1.667,0.365 10 false BDL- 2.844,3.469 4.51,3.833 1.667,0.365 10 false 2 3.448,2.885 5.115,3.25 1.667,0.365 10 false JM3 3.521,2.688 5.188,3.052 1.667,0.365 10 false 1 3.531,3.375 5.198,3.74 1.667,0.365 10 false 2 4.208,2.781 5.875,3.146 1.667,0.365 10 false 2 4.208,3.458 5.875,3.823 1.667,0.365 10 false 1 4.375,2.781 6.042,3.146 1.667,0.365 10 false BDL+ 4.375,3.458 6.042,3.823 1.667,0.365 10 false BDL- 0.563,4.125 2.229,4.49 1.667,0.365 10 false M62 0.563,4.292 3.344,4.573 2.781,0.281 10 false Rear Airbag Sensor LH 4.333,4.125 6,4.49 1.667,0.365 10 false J27 4.333,4.302 6.823,4.594 2.49,0.292 10 false Side Airbag Sensor Assembly LH 3.438,3.573 5.104,3.938 1.667,0.365 10 false JM3

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly LH and rear airbag sensor LH. Also check that the connectors that link the No. 2 floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH. Also disconnect the connectors that link the No. 2 floor wire and front door wire LH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS

NG

REPLACE NO. 2 FLOOR WIRE OR FRONT DOOR WIRE LH

3.CHECK WIRE HARNESS
a.
C295812C56
0.552,3.615 0.927,3.833 0.375,0.219 0.823,0.667 1.219,0.917 0.396,0.25 1.958,2.854 1.958,2.469 false 2.052,4.167 1.656,3.76 false 1.531,4.385 1.531,4.219 false 1.448,1.24 1.76,0.781 false 2.219,1.24 1.938,0.781 false 1.448,2.344 1.448,1.771 1.448,1.771 1.271,1.771 false 0.938,4.156 1.375,3.75 false 0.552,2.333 1.042,2.781 0.49,0.448 10 false *1 2.719,2.333 3.208,2.802 0.49,0.469 10 false *2 1.469,4.385 1.854,4.667 0.385,0.281 10 false *5 0.635,0.177 1.073,0.656 0.438,0.479 10 false *a 0.354,3.167 0.792,3.813 0.438,0.646 10 false *b 2.385,2.333 2.875,2.802 0.49,0.469 10 false A 2.083,2.333 2.573,2.802 0.49,0.469 10 false B 1.74,2.333 2.229,2.802 0.49,0.469 10 false C 1.583,2.333 2.073,2.802 0.49,0.469 10 false D 1.229,2.333 1.719,2.802 0.49,0.469 10 false E 0.927,2.333 1.417,2.802 0.49,0.469 10 false F 1.302,1.25 1.844,1.521 0.542,0.271 10 false BDL+ 2.083,1.25 2.75,1.667 0.667,0.417 10 false BDL- 1.906,4.167 2.406,4.635 0.5,0.469 10 false BDL+ 0.792,4.167 1.292,4.5 0.5,0.333 10 false BDL- 0.896,0.708 1.438,0.979 0.542,0.271 10 false M62 0.635,3.646 1.177,3.917 0.542,0.271 10 false J27 1.104,1.688 1.604,2.021 0.5,0.333 10 false *3 1.896,2.875 2.396,3.208 0.5,0.333 10 false *4
*1 Side Airbag Sensor Assembly LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 No. 2 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the connectors that link the No. 2 floor wire and front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M62-1 (BDL+) - Body ground Ignition switch ON Below 1 V
M62-2 (BDL-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (BDL+) - M62-2 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (BDL+) - M62-2 (BDL-) Always 1 MΩ or higher
M62-1 (BDL+) - Body ground Always 1 MΩ or higher
M62-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK REAR AIRBAG SENSOR LH

NG

6.CHECK NO. 2 FLOOR WIRE
4.CHECK REAR AIRBAG SENSOR LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Rear Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the side airbag sensor assembly LH.


b.

Interchange the rear airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B167B or B167C is output. A
DTC B166D or B166E is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.



A

5.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

B

C

5.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor LH


Interchange the side airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B167B or B167C is output. A
DTC B166D or B166E is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

6.CHECK NO. 2 FLOOR WIRE
a.
B566952C02
0.854,0.823 1.229,1.073 0.375,0.25 1.094,3.615 1.479,3.833 0.385,0.219 2.385,3.427 2.052,3.5 false 1.844,1.542 1.844,1.333 false 1.333,1.406 1.771,0.906 false 2.333,1.406 1.917,0.906 false 1.333,2.479 1.333,2.729 false 1.906,2.01 2.073,2.01 2.073,2.01 2.073,2.344 false 1.469,3.427 1.813,3.49 false 0.417,2.323 0.813,2.729 0.396,0.406 10 false *1 2.865,2.323 3.26,2.896 0.396,0.573 10 false *2 1.271,2.74 1.604,2.979 0.333,0.24 10 false *3 1.75,1.938 2.146,2.271 0.396,0.333 10 false *4 1.781,1.552 2.198,1.875 0.417,0.323 10 false *5 0.646,0.417 1.042,0.833 0.396,0.417 10 false *a 1.021,3.156 1.417,3.563 0.396,0.406 10 false *b 2.542,2.323 2.938,2.896 0.396,0.573 10 false A 2.24,2.323 2.635,2.896 0.396,0.573 10 false B 1.813,2.323 2.208,2.896 0.396,0.573 10 false C 1.521,2.323 1.917,2.896 0.396,0.573 10 false D 1.094,2.323 1.49,2.896 0.396,0.573 10 false E 0.792,2.323 1.188,2.896 0.396,0.573 10 false F 1.177,1.427 1.677,1.76 0.5,0.333 10 false BDL+ 2.208,1.427 2.708,1.76 0.5,0.333 10 false BDL- 2.427,3.344 3.281,3.583 0.854,0.24 10 false BDL+ 1.135,3.354 1.635,3.688 0.5,0.333 10 false BDL- 0.917,0.865 1.417,1.198 0.5,0.333 10 false M62 1.167,3.635 1.667,3.969 0.5,0.333 10 false JM3
*1 Side Airbag Sensor Assembly LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 No. 2 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the No. 2 floor wire connector from the front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
JM3-1 (BDL+) - Body ground Ignition switch ON Below 1 V
JM3-2 (BDL-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM3-1 (BDL+) - JM3-2 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM3-1 (BDL+) - JM3-2 (BDL-) Always 1 MΩ or higher
JM3-1 (BDL+) - Body ground Always 1 MΩ or higher
JM3-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE NO. 2 FLOOR WIRE