Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0418174 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then turns off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

If a malfunction occurs in the airbag sensor assembly, combination meter assembly or wire harness connected to the airbag sensor assembly or combination meter assembly, the SRS warning light turns on.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the power source voltage drops.

When the auxiliary battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically turns off when the power source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly via CAN communication.

WIRING DIAGRAM

B519421E06
0.167,1.813 1.74,2.354 1.573,0.542 10 false from Auxiliary Battery 4.906,0.729 5.781,0.979 0.875,0.25 10 false A/BAG-IG2 2.094,1.417 3.135,1.708 1.042,0.292 10 false METER-IG2 1.958,1.969 3.073,2.479 1.115,0.51 10 false ECU-DCC NO. 2 3.094,2.365 3.396,2.635 0.302,0.271 10 false ES 2.875,1.729 3.146,2.021 0.271,0.292 10 false 40 2.865,1.177 3.188,1.427 0.323,0.25 10 false 39 5.802,1.115 6.208,1.385 0.406,0.271 10 false 26 4.094,1.125 4.417,1.375 0.323,0.25 10 false 32 2.865,2.271 3.26,2.594 0.396,0.323 10 false 21 6.052,0.594 6.427,0.906 0.375,0.313 10 false IG2 3.615,1.26 4.302,1.583 0.688,0.323 10 false CANH 3.635,1.823 4.25,2.177 0.615,0.354 10 false CANL 6.063,2.365 6.354,2.625 0.292,0.26 10 false E1 6.063,2.875 6.354,3.125 0.292,0.25 10 false E2 5.99,3.625 6.5,3.917 0.51,0.292 10 false H58 3.042,3.604 3.448,3.854 0.406,0.25 10 false H21 5.979,3.792 6.896,4.448 0.917,0.656 10 false Airbag Sensor Assembly 3.042,3.771 4.24,4.333 1.198,0.563 10 false Combination Meter Assembly 5.802,1.677 6.313,1.958 0.51,0.281 10 false 27 6.052,1.26 6.583,1.5 0.531,0.24 10 false CANH 6.052,1.802 6.552,2.021 0.5,0.219 10 false CANL 5.802,0.49 6.25,0.781 0.448,0.292 10 false 36 5.813,2.271 6.208,2.521 0.396,0.25 10 false 33 5.813,2.781 6.104,2.979 0.292,0.198 10 false 32 4.094,1.677 4.5,2.031 0.406,0.354 10 false 31 3.104,1.813 3.406,2.031 0.302,0.219 10 false B 3.104,1.26 3.479,1.49 0.375,0.229 10 false IG+ 0.74,4.469 2.51,4.771 1.771,0.302 10 false : CAN Communication Line 2.948,0.573 4.458,0.885 1.51,0.313 10 false from IG2-NO. 2 Relay 0.156,1.271 2.042,1.542 1.885,0.271 10 false from IG2-NO. 2 Relay 3.094,2.885 3.396,3.156 0.302,0.271 10 false EP 2.917,2.781 3.219,3.052 0.302,0.271 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE
a.

for Gasoline Model:

i.

Measure the voltage of the auxiliary battery.

Standard Voltage:

11 to 14 V




b.

for HV Model:

i.

Measure the voltage of the auxiliary battery with the ignition switch off.

Standard Voltage:

11 to 14 V




Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR

NG

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the combination meter assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

3.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
C241761C76
0.25,0.417 0.667,0.667 0.417,0.25 0.479,1.927 0.885,1.729 false 3.094,1.667 3.094,0.385 3.094,0.385 2.802,0.385 true 0.427,1.313 0.979,1.563 false 2.969,1.698 2.969,0.594 2.969,0.594 2.677,0.594 true 0.083,0.052 0.51,0.406 0.427,0.354 10 false *a 2.427,0.51 2.76,0.729 0.333,0.219 10 false IG+ 2.677,0.313 2.938,0.531 0.26,0.219 10 false B 0.26,1.865 0.563,2.135 0.302,0.271 10 false ES 0.333,0.458 0.708,0.74 0.375,0.281 10 false H21 0.208,1.229 0.51,1.5 0.302,0.271 10 false EP
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for Gasoline Model):
Tester Connection Condition Specified Condition
H21-39 (IG+) - Body ground Ignition switch ON 11 to 14 V
H21-40 (B) - Body ground Always 11 to 14 V


Standard Voltage (for HV Model):
Tester Connection Condition Specified Condition
H21-39 (IG+) - Body ground Ignition switch ON 11 to 14 V
H21-40 (B) - Body ground Ignition switch off 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-21 (ES) - Body ground Always Below 1 Ω
H21-2 (EP) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE WIRE HARNESS

4.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Disconnect the connector from the airbag sensor assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY