Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0418174 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1651  Manual Cut OFF Switch Trouble  


DESCRIPTION

The airbag cut off switch circuit consists of the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

The instrument panel passenger airbag assembly can be optionally deactivated via this circuit by turning the airbag cut off switch cylinder sub-assembly to the OFF position.

If the instrument panel passenger airbag assembly is deactivated, the passenger airbag ON/OFF indicator ("OFF") comes on to inform the driver.

DTC B1651 is stored when a malfunction is detected in the airbag cut off switch circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1651 Manual Cut OFF Switch Trouble
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the airbag cut off switch circuit.

·

Airbag cut off switch cylinder sub-assembly malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Airbag cut off switch cylinder sub-assembly

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B512690E11
4.854,2.979 5.438,3.313 0.583,0.333 10 false H58 4.854,3.146 6.594,3.542 1.74,0.396 10 false Airbag Sensor Assembly 0.542,2.823 1.125,3.156 0.583,0.333 10 false H54 0.542,2.99 3.542,3.292 3,0.302 10 false Airbag Cut Off Switch Cylinder Sub-assembly 2.219,1.115 2.802,1.448 0.583,0.333 10 false 2 1.729,1.115 2.313,1.448 0.583,0.333 10 false PMC+ 1.75,2.302 2.333,2.635 0.583,0.333 10 false PMC- 2.208,2.302 2.792,2.635 0.583,0.333 10 false 1 4.885,1.104 5.469,1.438 0.583,0.333 10 false MSW+ 4.635,1.104 5.219,1.438 0.583,0.333 10 false 22 4.885,2.302 5.469,2.635 0.583,0.333 10 false MSW- 4.635,2.302 5.219,2.635 0.583,0.333 10 false 21

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE
a.
B512677C09
0.781,0.854 1.146,1.073 0.365,0.219 0.531,3.74 0.896,3.958 0.365,0.219 1.458,2.604 1.458,2.104 1.458,2.104 1.292,2.104 false 1.792,1.729 1.792,1.604 false 1.292,1.594 1.76,1.094 false 2.281,1.594 1.833,1.094 false 0.99,4.26 1.229,3.927 false 1.688,4.26 1.479,3.927 false 0.448,2.573 0.854,2.979 0.406,0.406 10 false *1 2.552,2.563 3.073,3.208 0.521,0.646 10 false *2 1.135,2.021 1.51,2.406 0.375,0.385 10 false *3 1.729,1.74 2.125,1.979 0.396,0.24 10 false *4 0.667,0.198 1.073,0.542 0.406,0.344 10 false *a 0.375,3.406 0.792,3.719 0.417,0.313 10 false *b 2.177,2.563 2.698,3.208 0.521,0.646 10 false A 1.813,2.563 2.333,3.208 0.521,0.646 10 false B 1.063,2.573 1.583,3.219 0.521,0.646 10 false C 0.698,2.573 1.219,3.219 0.521,0.646 10 false D 0.844,0.875 1.25,1.219 0.406,0.344 10 false H58 1.115,1.604 1.604,1.99 0.49,0.385 10 false MSW- 2.125,1.604 2.667,2.01 0.542,0.406 10 false MSW+ 1.563,4.271 2.177,4.604 0.615,0.333 10 false PMC+ 0.833,4.271 1.448,4.604 0.615,0.333 10 false PMC- 0.594,3.76 1,4.104 0.406,0.344 10 false H54
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H54-2 (PMC+) - Body ground Ignition switch ON Below 1 V
H54-1 (PMC-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 22 (MSW+) and 21 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-2 (PMC+) - H54-1 (PMC-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-2 (PMC+) - H54-1 (PMC-) Always 1 MΩ or higher
H54-2 (PMC+) - Body ground Always 1 MΩ or higher
H54-1 (PMC-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY
a.
C261687C14
2.281,1.052 2.729,0.771 false 2.281,1.135 2.729,1.417 false 0.073,0.063 0.354,0.365 0.281,0.302 10 false *a 2.781,0.698 3.25,1.042 0.469,0.344 10 false PMC+ 2.792,1.333 3.26,1.677 0.469,0.344 10 false PMC-
*a Component without harness connected
(Airbag Cut Off Switch Cylinder Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (PMC+) - 1 (PMC-) Cut off switch in ON position 360 to 440 Ω
2 (PMC+) - 1 (PMC-) Cut off switch in OFF position 90 to 110 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

5.CHECK DTC
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1651 is not output.


HINT:

Codes other than DTC B1651 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG