Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for HV Model)
RM37A0E _51 Engine / Hybrid System _086858 CRUISE CONTROL _0418319 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model) U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model)  TERMINALS OF ECU  


CHECK HYBRID VEHICLE CONTROL ECU


C338835E24
1.25,0.323 1.667,0.583 0.417,0.26 3.271,0.292 3.688,0.552 0.417,0.26 5.313,0.302 5.729,0.563 0.417,0.26 1.333,0.375 1.792,0.573 0.458,0.198 10 false A31 3.354,0.344 3.813,0.542 0.458,0.198 10 false A32 5.396,0.354 5.854,0.552 0.458,0.198 10 false H67

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Terminal Description Condition Specified Condition
A31-7 (STP) - H67-3 (E1) Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
A32-28 (ST1-) - H67-3 (E1) Stop light switch assembly signal Ignition switch ON, brake pedal depressed Below 1 V
Ignition switch ON, brake pedal released 11 to 14 V
H67-14 (CCS) - H67-3 (E1) Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 228 to 252 Ω
+RES switch pushed 599 to 661 Ω
-SET switch pushed 1463 to 1617 Ω



CHECK FORWARD RECOGNITION CAMERA


B472992E19
2.073,0.833 2.458,1.042 0.385,0.208 2.146,0.854 2.458,1.052 0.313,0.198 10 false R5

NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the forward recognition camera connector.



a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
R5-3 (LKSW) - R5-10 (GND) Steering pad switch assembly signal (distance control signal) Ignition switch ON, vehicle-to-vehicle distance control switch on Below 1 V
Ignition switch ON, vehicle-to-vehicle distance control switch off 4.75 to 5.25 V
R5-7 (IGB) - R5-10 (GND) Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
R5-10 (GND) - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
R5-5 (CA1P) - R5-10 (GND) CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
R5-6 (CANH) - R5-10 (GND) CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
R5-11 (CA1N) - R5-10 (GND) CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
R5-12 (CANL) - R5-10 (GND) CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)

i.
A438764N02
3.031,1.406 3.344,1.698 0.313,0.292 10 false GND

Waveform 1

Item Content
Tester Connection
·

Between R5-5 (CA1P) and R5-10 (GND)

·

Between R5-6 (CANH) and R5-10 (GND)


Tool Setting 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A438765N02
3.031,1.375 3.406,1.625 0.375,0.25 10 false GND

Waveform 2

Item Content
Tester Connection
·

Between R5-11 (CA1N) and R5-10 (GND)

·

Between R5-12 (CANL) and R5-10 (GND)


Tool Setting 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.