22271
1.INSTALL THROTTLE BODY GASKET
| *a | Protrusion |
Install a new throttle body gasket to the intake air surge tank assembly with the protrusion of the throttle body gasket oriented as shown in the illustration.
22030
2.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Install the throttle body with motor assembly to the intake air surge tank assembly with the 4 bolts.
If the throttle body with motor assembly has been struck or dropped, replace it.
Connect the throttle body with motor assembly connector.
| *1 | No. 2 Water By-pass Hose |
| *2 | No. 3 Water By-pass Hose |
| *a | Top |
| *b | Left Side of Vehicle |
| *c | Front of Vehicle |
| *d | Paint Mark |
| *e | 90° (Claw of Clip Location) |
Connect the No. 2 water by-pass hose and No. 3 water by-pass hose to the throttle body with motor assembly and slide the 2 clips to secure them.
Make sure to position each clip as shown in the illustration.
17705
3.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
| *a | Protrusion |
| *b | Cutout |
| *c | Hose Clamp End |
| *d | 2.0 mm (0.0787 in.) (End of Hose Clamp Location) |
| *e | Paint Mark |
Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly.
Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.
Tighten the hose clamp in the position shown in the illustration.
Make sure that the end of the hose clamp is positioned as shown in the illustration.
Engage the 2 guides.
Engage the 2 air cleaner cap clamps to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.
| *1 | No. 1 Fuel Vapor Feed Hose |
| *2 | No. 2 Ventilation Hose |
| *3 | Vacuum Hose Bracket |
| *a | Top |
| *b | Paint Mark |
| *c | Rear of Vehicle |
| *d | 180° (Claw of Clip Location) |
Connect the No. 2 ventilation hose to the air cleaner hose and slide the clip to secure it.
Make sure to position the clip as shown in the illustration.
Engage the 2 clamps to connect the No. 1 fuel vapor feed hose to the air cleaner hose.
Install the vacuum hose bracket to the air cleaner hose.
Connect the vacuum hose to the air cleaner hose.
Engage the 2 wire harness clamps.
Connect the mass air flow meter sub-assembly connector.
4.ADD ENGINE COOLANT
5.INSPECT FOR COOLANT LEAK
6.PERFORM INITIALIZATION
Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.
Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.
Clear the DTCs.
Perform "Inspection After Repair".
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.
650 to 750 rpm
Be sure to perform this step with all accessories off.
Make sure that the shift lever is in P or N.
Fully depress the accelerator pedal and check that the value is 60% or higher.
| Tester Display |
|---|
| Throttle Position Sensor No.1 Voltage % |
Perform a road test and confirm that there are no abnormalities.