Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › THROTTLE BODY › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418437 THROTTLE BODY A

2GR-FKS ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during throttle body with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 17705 2.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A454750

Disconnect the mass air flow meter sub-assembly connector.


b.

Disengage the 2 wire harness clamps.


c.

Disconnect the vacuum hose from the air cleaner hose.


d.
A454751C01
2.115,1.104 2.688,1.104 true 2.729,1.01 3.042,1.167 0.313,0.156 10 true *1 0.885,1.177 1.083,1.365 0.198,0.188 10 true *2 1.375,0.573 1.604,0.74 0.229,0.167 10 true *3
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Ventilation Hose
*3 Vacuum Hose Bracket


Remove the vacuum hose bracket from the air cleaner hose.


e.

Disengage the 2 clamps to disconnect the No. 1 fuel vapor feed hose from the air cleaner hose.


f.

Slide the clip and disconnect the No. 2 ventilation hose from the air cleaner hose.


g.
A454752C01
1.094,1.927 1.302,2.115 0.208,0.188 10 true *a 1.156,0.073 1.375,0.26 0.219,0.188 10 true *b 1.948,0.073 2.167,0.26 0.219,0.188 10 true *b 2.292,1.688 2.5,1.875 0.208,0.188 10 true *a
*a Air Cleaner Cap Clamp
*b Guide


Disengage the 2 air cleaner cap clamps.


h.

Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


i.
A454753

Loosen the hose clamp and remove the air cleaner cap with air cleaner hose from the throttle body with motor assembly.


Hide 22030 3.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A454754C01
1.917,1.448 2.292,1.448 true 1.198,1.729 1.198,1.375 true 1.146,1.74 1.385,1.917 0.24,0.177 10 true *1 2.313,1.375 2.542,1.552 0.229,0.177 10 true *2
*1 No. 2 Water By-pass Hose
*2 No. 3 Water By-pass Hose


Slide the 2 clips and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the throttle body with motor assembly.


b.
A454755

Disconnect the throttle body with motor assembly connector.


c.

Remove the 4 bolts and throttle body with motor assembly from the intake air surge tank assembly.

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



Hide 22271 4.REMOVE THROTTLE BODY GASKET

a.
A454756

Remove the throttle body gasket from the intake air surge tank assembly.