Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417739 WIRELESS DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B520311N39
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.292,6.198 5.729,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false H42 2.042,1.479 2.354,1.677 0.313,0.198 10 false H43 2.042,1.802 2.354,2 0.313,0.198 10 false H44 0.865,1.073 1.177,1.271 0.313,0.198 10 false 4D 0.865,1.656 1.177,1.854 0.313,0.198 10 false 4C 0.875,2.021 1.188,2.219 0.313,0.198 10 false 4E 0.896,2.25 1.208,2.448 0.313,0.198 10 false 4F 5.844,1.146 6.156,1.344 0.313,0.198 10 false 4B 5.844,1.76 6.156,1.958 0.313,0.198 10 false 4A 1.229,3.281 1.542,3.479 0.313,0.198 10 false H44 3.25,3.25 3.563,3.448 0.313,0.198 10 false H43 5.531,3.24 5.844,3.438 0.313,0.198 10 false H42 1.833,4.604 2.146,4.802 0.313,0.198 10 false 4A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 4C 3.813,6.156 4.125,6.354 0.313,0.198 10 false 4D 5.427,6.219 5.74,6.417 0.313,0.198 10 false 4F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 4E 5.51,4.604 5.823,4.802 0.313,0.198 10 false 4B

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground Ground Always Below 1 Ω
H42-19 (GND2) - Body ground Ground Always Below 1 Ω
MB-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
MB-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
MB-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

*1: for HV Model

*2: for Gasoline Model



d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
4C-29 (BZR) - Body ground* Wireless door lock buzzer output Active Test Wireless Buzzer is OFF Below 1 V
Active Test Wireless Buzzer is ON Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)

*: w/ Wireless Door Lock Buzzer Answer-back Function




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B506743C04
3.25,0.458 3.646,0.698 0.396,0.24 2.063,0.458 2.458,0.698 0.396,0.24 4.552,0.458 4.948,0.698 0.396,0.24 2.146,0.51 2.604,0.708 0.458,0.198 10 false A19 2.51,0.49 2.823,0.688 0.313,0.198 10 false *A 3.354,0.49 3.667,0.688 0.313,0.198 10 false M5 4.625,0.49 5.083,0.688 0.458,0.198 10 false H48
*A for Gasoline Model - -


a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H48-4 (+B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
H48-18 (E) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the H48 certification ECU (smart key ECU assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M5-18 (RCO) - H48-18 (E) Output to electrical key and tire pressure warning ECU and receiver
(Power supply for electrical key and tire pressure warning ECU and receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Turn ignition switch off

2.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

3.

Press lock or unlock switch of electrical key transmitter sub-assembly


Plus generation (See waveform 1)
M5-19 (RDAM) - H48-18 (E) Electrical key and tire pressure warning ECU and receiver communication circuit
Procedure:
1.

Turn ignition switch off

2.

Lock all doors

3.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

4.

Press lock or unlock switch of electrical key transmitter sub-assembly


Plus generation (See waveform 2)
M5-20 (CSEL) - H48-18 (E) Communication channel switching circuit
Procedure:
1.

Turn ignition switch off

2.

Close all doors


No pulse generation → Pulse generation


e.
B251178C30
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester connection M5-18 (RCO) - H48-18 (E)
Tool setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Turn ignition switch off

2.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

3.

Press lock or unlock switch of electrical key transmitter sub-assembly




f.
B251177C33
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester connection M5-19 (RDAM) - H48-18 (E)
Tool setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Turn ignition switch off

2.

Lock all doors

3.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

4.

Press lock or unlock switch of electrical key transmitter sub-assembly