Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › PATTERN SELECT SWITCH
RM37A0E _52 Drivetrain _086859 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0418480 PATTERN SELECT SWITCH G

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  PATTERN SELECT SWITCH  INSPECTION  


PROCEDURE

Hide 84720K 1.INSPECT SNOW SWITCH (PATTERN SELECT SWITCH)

a.
C426843C01
0.667,1.917 0.917,1.917 0.917,1.917 1.125,1.365 true 2.635,1.917 2.385,1.917 2.385,1.917 2.219,1.365 true 2.698,1.823 2.854,2.021 0.156,0.198 10 false E 0.375,1.823 0.708,2.073 0.333,0.25 10 false 2ND 0.167,0.167 0.5,0.333 0.333,0.167 10 false *a
*a Component without harness connected
(Snow Switch (Pattern Select Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (2ND) - 2 (E) Snow switch on (Push) Below 1 Ω
Snow switch off (Release) 10 kΩ or higher


If the result is not as specified, replace the snow switch (pattern select switch).


b.
C426843C02
0.5,1.917 0.625,1.917 0.625,1.917 0.833,1.365 true 2.833,1.917 2.729,1.917 2.729,1.917 2.563,1.365 true 2.885,1.833 3.219,2.083 0.333,0.25 10 false ILL- 0.208,1.823 0.625,2.073 0.417,0.25 10 false ILL+ 0.167,0.167 0.583,0.365 0.417,0.198 10 false *a
*a Component without harness connected
(Snow Switch (Pattern Select Switch))


Apply battery voltage between the terminals of the snow switch (pattern select switch), and check the illumination condition of the snow switch (pattern select switch).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (ILL+)
Battery negative (-) → Terminal 1 (ILL-)
Illuminates


If the result is not as specified, replace the snow switch (pattern select switch).


Hide 84720A 2.INSPECT NO. 1 PATTERN SELECT SWITCH ASSEMBLY

a.
C426844C01
1,3.25 1.25,3.25 1.25,3.25 1.458,2.75 true 2.667,3.25 2.417,3.25 2.417,3.25 2.25,2.75 true 1.781,3.198 1.781,2.75 true 0.5,1.583 0.771,1.781 0.271,0.198 10 false *a 0.719,3.167 1.177,3.365 0.458,0.198 10 false SEL 1.74,3.219 2.094,3.396 0.354,0.177 10 false E 2.74,3.167 3.198,3.365 0.458,0.198 10 false E
*a Component without harness connected
(No. 1 Pattern Select Switch Assembly)
V113147

"DRIVE MODE +" Side
V113148

"DRIVE MODE -" Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (SEL) - 5 (E) Pushed and held at "DRIVE MODE +" side Below 50 Ω
Released (neutral position) 10 kΩ or higher
6 (E) - 5 (E) Pushed and held at "DRIVE MODE -" side Below 50 Ω
Released (neutral position) 10 kΩ or higher


If the result is not as specified, replace the No. 1 pattern select switch assembly.


b.
C427038C01
0.604,1 1.104,1 true 2.26,1 2.76,1 true 0.521,0.25 0.833,0.448 0.313,0.198 10 false *a 0.313,0.906 0.729,1.188 0.417,0.281 10 false ILL- 2.813,0.906 3.229,1.188 0.417,0.281 10 false ILL+
*a Component without harness connected
(No. 1 Pattern Select Switch Assembly)


Apply battery voltage between the terminals of the No. 1 pattern select switch assembly, and check the illumination condition of the No. 1 pattern select switch assembly.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (ILL+)
Battery negative (-) → Terminal 4 (ILL-)
Illuminates


If the result is not as specified, replace the No. 1 pattern select switch assembly.