Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418593 POWER BACK DOOR SYSTEM W

DOOR / HATCH  POWER BACK DOOR SYSTEM  CUSTOMIZE PARAMETERS  


CUSTOMIZE POWER BACK DOOR SYSTEM


NOTICE:
·

When the customer requests a change in a function, first make sure that the function can be customized.

·

Record the current settings before customizing.



HINT:

The following items can be customized.


a.

Customizing with the GTS.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Customize Setting / PSD & PBD operation.


v.

Select the setting by referring to the table below.

PSD & PBD operation
Tester Display Description Default Setting ECU
PBD SW Operation Function that changes the time necessary to operate the power back door control switch between pressed once and held down for 0.8 seconds. 0.8s 0:0.0s,1:0.8s Multiplex network door ECU
PBD Buzzer Function that changes the power back door warning buzzer setting. ON*1
OFF*2
0:OFF,1:ON Multiplex network door ECU
Door Unlock with 1 Motion. Function that selects the back door or doors to unlock when the back door is locked and the transmitter switch (electrical key transmitter sub-assembly) is pressed to operate the power back door. ALL DOORS 0:BackDoor,1:ALL DOORS Multiplex network door ECU
Wireless Power Back Door Open Function that operates the power back door by pressing the transmitter switch (electrical key transmitter sub-assembly). Lock:OFF/Unlock:0.8s 0000:"Lock:OFF/Unlock:OFF",0001:"Lock:OFF/Unlock:ON",0010:"Lock:OFF/Unlock:Twice",0011:"Lock:OFF/Unlock:0.8s",1010:"Lock:Twice/Unlock:Twice",1011:"Lock:0.8s/Unl**cut** Multiplex network door ECU
PBD Assist Open Operation Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated. ON 0:OFF,1:ON Multiplex network door ECU
PBD/Emblem Sensor Function Function that enables/disables the power back door and rear emblem sensor assembly.*3 PBD ON/Emblem ON 00:PBD OFF/Emblem OFF,01:PBD ON/Emblem OFF,10:PBD ON/Emblem ON Multiplex network door ECU
PBD Buzzer Volume Adjust Function that changes the volume setting of the power back door warning buzzer. Large 00:Small,01:Middle,10:Large Multiplex network door ECU
Emblem Sensor Detection Sensitivity Function that changes the sensitivity of the rear emblem sensor assembly.*3 Low 00:Low,01:Middle,10:High Multiplex network door ECU
Kick Sensor Function Function that enables/disables the hands free power back door*3 ON 0:OFF,1:ON Multiplex network door ECU
PBD Assist Close Operation Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. ON 0:OFF,1:ON Multiplex network door ECU
Power Back Door Opening Adjust Function that changes the position that the power back door stops during an open operation. 5:Max 000:"1:Min",001:"2:Small",010:"3:Middle",011:"4:Large",100:"5:Max",111:User Setting Position Multiplex network door ECU
Kick Sensor Operation with ACC ON Status of the hands free power back door function with ignition switch ACC.*3 Not Available 0:Available,1:Not Available Main body ECU (multiplex network body ECU)
50006 21

**cut** = ock:0.8s"

*1: w/ Power Back Door Hazard Warning Light

*2: w/o Power Back Door Hazard Warning Light

*3: Although the item is displayed on the GTS, it is not applicable to this vehicle.




b.

Customizing with the multi-information display (combination meter assembly)

i.

Turn the ignition switch to ON.


ii.

Enter the following menus: Vehicle Settings / Power Back Door.


iii.

Select the setting by referring to the table below.

Display Description Default Setting Relevant ECU
System Settings Function that enables/disables the power back door. ON OFF / ON Multiplex network door ECU
Opening Adjustment Function that changes the position that the power back door stops during an open operation. 5 User Setting Position, 5, 4, 3, 2 or 1 Multiplex network door ECU
Volume Function that changes the volume setting of the power back door buzzer. 3 1/2/3 Multiplex network door ECU