CHECK MULTIPLEX NETWORK DOOR ECU
Disconnect the W18 and W19 multiplex network door ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| W18-20 (ECUB) - Body ground | Auxiliary battery power supply | Ignition switch off*1
Always*2 |
11 to 14 V |
| W18-18 (IG) - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| W19-1 (B) - Body ground | Auxiliary battery power supply | Ignition switch off*1
Always*2 |
11 to 14 V |
| W19-10 (GND) - Body ground | Body ground | Always | Below 1 Ω |
*1: for HV Model
*2: for Gasoline Model
Reconnect the W18 and W19 multiplex network door ECU connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| W18-1 (DS1) - Body ground | Power back door unit assembly set LH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation
(See waveform 1) |
||
| W18-2 (DS2) - Body ground | Power back door unit assembly set LH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation
(See waveform 2) |
||
| W18-3 (DS12) - Body ground | Power back door unit assembly set RH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation
(See waveform 1) |
||
| W18-4 (DS22) - Body ground | Power back door unit assembly set RH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation
(See waveform 2) |
||
| W18-5 (DSV2) - Body ground | Power back door unit assembly set RH (door sensor) power supply | Always | 7 V or higher |
| W18-6 (OSR) - W18-24 (OSE) | Power back door sensor assembly RH signal | Power back door sensor assembly RH not pressed | 4 to 6 V |
| Power back door sensor assembly RH pressed | Below 1 V | ||
| W18-8 (BDDN) - Body ground | No. 1 power back door control switch | No. 1 power back door control switch on | Below 1 V |
| No. 1 power back door control switch off | Pulse generation | ||
| W18-12 (LIB) - Body ground | Back door lock signal | Back door is locked | Below 1 V |
| Back door is unlocked | 11 to 14 V | ||
| W18-16 (BZR+) - Body ground | Wireless door lock buzzer signal | Active Test PBD Buzzer is ON | Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V) |
| Active Test PBD Buzzer is OFF | Below 1 V | ||
| W18-19 (DSG2) - Body ground | Power back door unit assembly set RH (door sensor) ground | Always | Below 1 V |
| W18-21 (DSG) - Body ground | Power back door unit assembly set LH (door sensor) ground | Always | Below 1 V |
| W18-25 (DSV) - Body ground | Power back door unit assembly set LH (door sensor) power supply | Always | 7 V or higher |
| W18-26 (OSL) - W18-24 (OSE) | Power back door sensor assembly LH signal | Power back door sensor assembly LH not pressed | 4 to 6 V |
| Power back door sensor assembly LH pressed | Below 1 V | ||
| W19-4 (DC+) - W19-3 (DC-) | Back door lock with courtesy light switch assembly (back door lock motor) circuit | Back door lock motor operating | 11 to 14 V |
| Back door lock motor not operating | Below 1 V |
Using an oscilloscope, check waveform 1.
| Item | Condition |
|---|---|
| Tester Connection | ·
W18-1 (DS1) - Body ground ·
W18-3 (DS12) - Body ground |
| Tool setting | 2 V/DIV., 2 ms/DIV. |
| Vehicle condition | Power back door operating |
The period changes in accordance with the speed at which the power back door is opened and closed.
Using an oscilloscope, check waveform 2.
| Item | Condition |
|---|---|
| Tester Connection | ·
W18-2 (DS2) - Body ground ·
W18-4 (DS22) - Body ground |
| Tool setting | 2 V/DIV., 2 ms/DIV. |
| Vehicle condition | Power back door operating |
The period changes in accordance with the speed at which the power back door is opened and closed.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
| *A | for Gasoline Model | - | - |
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H48-4 (+B) - Body ground | Auxiliary battery power supply | Ignition switch off*1
Always*2 |
11 to 14 V |
| H48-18 (E) - Body ground | Body ground | Always | Below 1 Ω |
*1: for HV Model
*2: for Gasoline Model
Reconnect the H48 certification ECU (smart key ECU assembly) connector.
Measure the waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| M5-26 (TSW5) - H48-18 (E) | Back door opener switch assembly (open switch) signal | Back door opener switch assembly (open switch) off → on | Pulse generation (See waveform 1) |
| *a | Checking for switch on signal at short intervals |
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | M5-26 (TSW5) - H48-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Back door opener switch assembly (open switch) off → on |
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Reconnect the instrument panel junction block assembly connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| MB-31 (BECU) - Body ground | Auxiliary battery power supply | Ignition switch off*1
Always*2 |
11 to 14 V |
| MB-32 (IG) - Body ground | Ignition power supply (IG signal) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| MB-30 (ACC) - Body ground | Ignition power supply (ACC signal) | Ignition switch off | Below 1 V |
| Ignition switch ACC | 11 to 14 V | ||
| MB-11 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| H42-19 (GND2) - Body ground | Ground | Always | Below 1 Ω |
| MB-4 (BCTY) - Body ground | Back door courtesy light switch input | Back door closed | 10 kΩ or higher |
| Back door open | Below 1 Ω |
*1: for HV Model
*2: for Gasoline Model
Install the main body ECU (multiplex network body ECU) to instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H44-4 (PBDS) - Body ground | Power back door control switch signal | Power back door control switch off | Pulse generation |
| Power back door control switch on | Below 1 V | ||
| H42-13 (LSBO) - Body ground | Back door lock signal | Back door is locked | Below 1 V |
| Back door is unlocked | 11 to 14 V | ||
| 4C-29 (BZR) - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer not operating | Below 1 V |
| Wireless door lock buzzer operating | Pulse generation |