Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM37A0E _58 Vehicle Interior _086887 LIGHTING (INT) _0418630 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E366421E56
0.708,0.552 2.167,0.802 1.458,0.25 10 false from Auxiliary Battery 2.583,0.708 3.094,0.938 0.51,0.229 10 false J/B 4.219,1.438 4.958,1.667 0.74,0.229 10 false ACC 4.896,0.74 5.708,0.979 0.813,0.24 10 false ECU-ACC 6.313,0.458 6.729,0.646 0.417,0.188 10 false ACC 0.208,1.177 2.031,1.75 1.823,0.573 10 false from Certification ECU (Smart Key ECU Assembly) 6.292,1.781 6.771,2 0.479,0.219 10 false GND1 5.896,1.792 6.198,2.031 0.302,0.24 10 false MB 5.885,0.563 6.188,0.802 0.302,0.24 10 false MB 3.219,0.552 3.49,0.802 0.271,0.25 10 false 4F 3.219,1.177 3.49,1.427 0.271,0.25 10 false 4A 3.219,1.792 3.49,2.042 0.271,0.25 10 false 4B 3.24,0.354 3.521,0.594 0.281,0.24 10 false 1 3.229,0.979 3.51,1.219 0.281,0.24 10 false 30 3.271,1.604 3.552,1.844 0.281,0.24 10 false 3 3.542,2.219 5.135,2.615 1.594,0.396 10 false Instrument Panel Junction Block Assembly 5.458,3.063 7.125,3.5 1.667,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 5.906,0.365 6.188,0.604 0.281,0.24 10 false 30 5.917,1.594 6.198,1.833 0.281,0.24 10 false 11 6.292,2.625 6.771,2.844 0.479,0.219 10 false GND2 5.875,2.625 6.177,2.865 0.302,0.24 10 false H42 5.917,2.427 6.219,2.667 0.302,0.24 10 false 19

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

First, check for entry and start system (for Start Function) DTCs, and after confirming that there is no malfunction, proceed with troubleshooting.

for Gasoline Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>DTC CHECK / CLEAR

for HV Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>DTC CHECK / CLEAR

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal OFF or ON OFF: Ignition switch off
ON: Ignition switch ACC
"ON" is also displayed for this item when the ignition switch is ON.
Body Electrical > Main Body > Data List
Tester Display
ACC SW
50003 123 31
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the 4F and 4B instrument panel junction block assembly connectors.


b.

Disconnect the H42 main body ECU (multiplex network body ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: for Gasoline Model

*2: for HV Model

4F-1 - Body ground Always*1
Ignition switch off*2
11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-3 - Body ground Always Below 1 Ω
H42-19 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E333577C45
1.698,0.51 2.042,0.729 0.344,0.219 4.938,0.531 5.281,0.75 0.344,0.219 2.438,2.438 2.781,2.656 0.344,0.219 5.729,2.292 6.073,2.51 0.344,0.219 4.01,3.094 4.188,3.375 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 1.781,0.531 2.198,0.771 0.417,0.24 10 false 4B 5.021,0.552 5.438,0.792 0.417,0.24 10 false 4A 2.5,2.448 2.917,2.688 0.417,0.24 10 false MB 5.823,2.313 6.24,2.552 0.417,0.24 10 false 4F 4.073,3.396 4.49,3.635 0.417,0.24 10 false ACC
*a Component without harness connected (Instrument Panel Junction Block Assembly) - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-1 - MB-30 (ACC) Auxiliary battery not connected to 4A-30 and 4B-3 10 kΩ or higher
4F-1 - MB-30 (ACC) Auxiliary battery positive (+) → 4A-30
Auxiliary battery negative (-) → 4B-3
Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY