Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM37A0E _58 Vehicle Interior _086887 LIGHTING (INT) _0418630 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls operation of the DOME CUT relay in order to supply power to the interior lights. When the battery saving function operates while the interior lights are on, the main body ECU (multiplex network body ECU) opens the DOME CUT relay to turn off the lights.

WIRING DIAGRAM

E401971E10
1.156,0.208 2.583,0.427 1.427,0.219 10 false from Auxiliary Battery 1.469,0.875 2.385,1.073 0.917,0.198 10 false J/B 3.24,0.875 3.719,1.063 0.479,0.188 10 false DOME 4.271,1.354 5.188,1.552 0.917,0.198 10 false DOME CUT 5.844,0.615 6.76,0.813 0.917,0.198 10 false DOMR 5.427,3.167 7.063,3.583 1.635,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 2.875,2.667 5.76,2.854 2.885,0.188 10 false Instrument Panel Junction Block Assembly 0.385,2.01 1.792,2.219 1.406,0.208 10 false to each Interior Light 2.594,0.719 3.063,0.906 0.469,0.188 10 false 4F 2.625,0.531 3.094,0.719 0.469,0.188 10 false 1 2.573,2.125 3.042,2.313 0.469,0.188 10 false 10 2.583,2.313 3.052,2.5 0.469,0.188 10 false 4B 2.615,1.51 3.083,1.698 0.469,0.188 10 false 9 2.583,1.708 3.052,1.896 0.469,0.188 10 false 4B 5.594,0.615 6.063,0.802 0.469,0.188 10 false 23 5.427,2.99 5.74,3.188 0.313,0.198 10 false MB

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME CUT relay OFF or ON When performing this Active Test, turn all the interior lights on.
·

OFF: DOME CUT relay on (interior lights turn on)

·

ON: DOME CUT relay off (interior lights turn off)


Body Electrical > Main Body > Active Test
Tester Display
Relay for Interior Light Auto Cut Function
50004 123 66
OK:

All of the interior lights turn off when ON is selected.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: for Gasoline Model

*2: for HV Model

4F-1 - Body ground Always*1
Ignition switch off*2
11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E361207C12
1.969,0.177 2.302,0.406 0.333,0.229 4.823,0.323 5.156,0.552 0.333,0.229 3.396,1.708 3.729,1.938 0.333,0.229 4.25,2.198 4.573,1.813 4.573,1.813 4.719,1.813 true 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 4.906,0.354 5.188,0.583 0.281,0.229 10 false 4F 2.052,0.208 2.333,0.438 0.281,0.229 10 false 4B 3.458,1.74 3.74,1.969 0.281,0.229 10 false MB 4.771,1.729 5.229,1.927 0.458,0.198 10 false DOMR
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4B-9 - Auxiliary battery negative (-) Auxiliary battery positive (+) → 4F-1
Auxiliary battery negative (-) → MB-23 (DOMR)
11 to 14 V
4B-10 - Auxiliary battery negative (-) Auxiliary battery positive (+) → 4F-1
Auxiliary battery negative (-) → MB-23 (DOMR)
11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-1 - 4B-9 Always 10 kΩ or higher
4F-1 - 4B-10 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY