Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM37A0E _58 Vehicle Interior _086887 LIGHTING (INT) _0418630 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Push Start Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the push start switch illumination.

WIRING DIAGRAM

E402365E11
1.479,2.156 3.313,2.354 1.833,0.198 10 false Push Start Switch 4.875,2.177 6.677,2.542 1.802,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.479,1.99 2.417,2.208 0.938,0.219 10 false H49*1, H50*2 4.875,2.01 5.198,2.188 0.323,0.177 10 false H48 5.073,1.323 5.49,1.521 0.417,0.198 10 false AGND 5.073,0.688 5.49,0.885 0.417,0.198 10 false SWIL 4.823,1.323 5.094,1.5 0.271,0.177 10 false 11 4.823,0.688 5.094,0.865 0.271,0.177 10 false 10 5.885,0.646 6.156,0.823 0.271,0.177 10 false +B 3.74,0.698 4.01,0.875 0.271,0.177 10 false 9 3.74,1.313 4.01,1.49 0.271,0.177 10 false 6 3.292,0.698 3.667,0.875 0.375,0.177 10 false SWIL 3.25,1.313 3.667,1.51 0.417,0.198 10 false AGND 0.25,2.448 3.615,2.646 3.365,0.198 10 false *1: for Gasoline Model 2.104,2.448 5.469,2.646 3.365,0.198 10 false *2: for HV Model

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Push start switch illumination OFF or ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Push start switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PUSH START SWITCH
2.INSPECT PUSH START SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (PUSH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for Gasoline Model):
Tester Connection Condition Specified Condition
H49-9 (SWIL) - H48-10 (SWIL) Always Below 1 Ω
H49-6 (AGND) - H48-11 (AGND) Always Below 1 Ω
H49-9 (SWIL) or H48-10 (SWIL) - Body ground Always 10 kΩ or higher
H49-6 (AGND) or H48-11 (AGND) - Body ground Always 10 kΩ or higher


Standard Resistance (for HV Model):
Tester Connection Condition Specified Condition
H50-9 (SWIL) - H48-10 (SWIL) Always Below 1 Ω
H50-6 (AGND) - H48-11 (AGND) Always Below 1 Ω
H50-9 (SWIL) or H48-10 (SWIL) - Body ground Always 10 kΩ or higher
H50-6 (AGND) or H48-11 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR