Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418696 SFI SYSTEM U

2GR-FKS ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A456833E01
2.344,0.375 2.792,0.677 0.448,0.302 5.771,0.417 6.219,0.719 0.448,0.302 2.469,0.427 2.927,0.625 0.458,0.198 10 false C54 5.875,0.469 6.333,0.667 0.458,0.198 10 false A28

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A28-1 (BATT) - C54-53 (E1) Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A28-2 (+B) - C54-53 (E1) Power source of ECM Ignition switch ON 11 to 14 V
A28-3 (+B2) - C54-53 (E1) Power source of ECM Ignition switch ON 11 to 14 V
A28-4 (IGSW) - C54-53 (E1) Ignition switch Ignition switch ON 11 to 14 V
A28-7 (IREL) - C54-53 (E1) D INJ relay operation signal Engine stopped, ignition switch ON 0 to 1.5 V
A28-8 (+BM) - C54-53 (E1) Power source of throttle actuator Always 11 to 14 V
A28-13 (CANH) - C54-53 (E1) CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 1)
A28-14 (EC) - Body ground Ground Always Below 1 Ω
A28-17 (S) - C54-53 (E1) M shift position switch signal Ignition switch ON and shift lever in M 11 to 14 V
Ignition switch ON and shift lever not in M Below 1 V
A28-18 (FPC) - C54-53 (E1) Fuel pump control Engine stopped, ignition switch ON Below 1.5 V
A28-26 (CANL) - C54-53 (E1) CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 2)
A28-27 (STP) - C54-53 (E1) Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A28-30 (NEO) - C54-53 (E1) Engine speed signal sent to other ECUs Idling with warm engine Pulse generation
(See waveform 3)
A28-39 (SPD) - C54-53 (E1) Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 4)
A28-40 (SPCN) - C54-53 (E1) Drive mode switch (NORMAL mode) Ignition switch ON 11 to 14 V
Ignition switch ON, NORMAL mode switch being pushed and held (NORMAL mode) 0 to 1.5 V
A28-42 (ST1-) - C54-53 (E1) Stop light switch assembly signal (opposite to STP terminal) Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A28-43 (STA) - C54-53 (E1) Starter assembly signal Cranking 6.0 V or higher
A28-46 (MREL) - C54-53 (E1) EFI-MAIN relay operation signal Ignition switch ON 11 to 14 V
A28-47 (VPA) - A28-48 (EPA) Accelerator pedal position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
A28-49 (VCPA) - A28-48 (EPA) Power source of accelerator pedal position sensor (for VPA) Engine stopped, ignition switch ON 4.5 to 5.5 V
A28-50 (VPA2) - A28-51 (EPA2) Accelerator pedal position sensor signal Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed 3.4 to 4.75 V
A28-52 (VCP2) - A28-51 (EPA2) Power source of accelerator pedal position sensor (for VPA2) Engine stopped, ignition switch ON 4.5 to 5.5 V
A28-55 (PWMS) - C54-53 (E1) Drive mode switch (SPORT mode) Ignition switch ON 11 to 14 V
Ignition switch ON, SPORT mode switch being pushed and held at SPORT position (SPORT mode) 0 to 1.5 V
A28-58 (KSW) - C54-53 (E1) Key in vehicle signal Ignition switch off → ON 0 to 3.0 V
C54-2 (OE2+) - C54-3 (OE2-) Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2) operation signal Idling Pulse generation
(See waveform 5)
C54-4 (OE1+) - C54-5 (OE1-) Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1) operation signal Idling Pulse generation
(See waveform 5)
C54-9 (OC2+) - C54-8 (OC2-) Cam timing oil control solenoid assembly (for intake camshaft of bank 2) operation signal Idling Pulse generation
(See waveform 6)
C54-16 (HT2B) - C54-53 (E1) Heated oxygen sensor (bank 2 sensor 2) heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C54-17 (HA2A) - C54-46 (E05) Air fuel ratio sensor (bank 2 sensor 1) heater operation signal Idling Pulse generation
(See waveform 7)
Ignition switch ON 11 to 14 V
C54-18 (+BD2) - C54-53 (E1) Power source of ECM (injector driver) Engine stopped, ignition switch ON 11 to 14 V
C54-19 (+BD1) - C54-53 (E1) Power source of ECM (injector driver) Engine stopped, ignition switch ON 11 to 14 V
C54-20 (E02) - Body ground Ground Always Below 1 Ω
C54-21 (E04) - Body ground Ground Always Below 1 Ω
C54-23 (FP1+) - C54-22 (FP1-) Fuel pump assembly (for high pressure side) signal Idling with warm engine Pulse generation
C54-24 (#6D+) - C54-54 (#6D-) No. 6 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C54-25 (#3D+) - C54-26 (#3D-) No. 3 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C54-27 (#5D+) - C54-57 (#5D-) No. 5 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C54-28 (#2D+) - C54-58 (#2D-) No. 2 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C54-29 (#4D+) - C54-59 (#4D-) No. 4 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C54-30 (#1D+) - C54-60 (#1D-) No. 1 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C54-34 (IGT6) - C54-53 (E1) No. 6 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C54-35 (IGT4) - C54-53 (E1) No. 4 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C54-36 (IGT2) - C54-53 (E1) No. 2 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C54-38 (OC1+) - C54-68 (OC1-) Cam timing oil control solenoid assembly (for intake camshaft of bank 1) operation signal Idling Pulse generation
(See waveform 6)
C54-39 (ACM) - C54-53 (E1) Vacuum switching valve (for active control engine mount system) operation signal Ignition switch ON 11 to 14 V
C54-40 (#60) - C54-51 (E01) No. 6 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C54-41 (#30) - C54-51 (E01) No. 3 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C54-42 (#50) - C54-51 (E01) No. 5 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C54-43 (#20) - C54-51 (E01) No. 2 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C54-44 (#40) - C54-51 (E01) No. 4 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C54-45 (#10) - C54-51 (E01) No. 1 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C54-46 (E05) - Body ground Ground Always Below 1 Ω
C54-47 (M-) - C54-49 (ME01) Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 10)
C54-48 (M+) - C54-49 (ME01) Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 11)
C54-49 (ME01) - Body ground Ground Always Below 1 Ω
C54-50 (HT1B) - C54-53 (E1) Heated oxygen sensor (bank 1 sensor 2) heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C54-51 (E01) - Body ground Ground Always Below 1 Ω
C54-52 (HA1A) - C54-21 (E04) Air fuel ratio sensor (bank 1 sensor 1) heater operation signal Idling Pulse generation
(See waveform 7)
Ignition switch ON 11 to 14 V
C54-53 (E1) - Body ground Ground Always Below 1 Ω
C54-55 (E1D2) - Body ground Ground Always Below 1 Ω
C54-56 (E1D1) - Body ground Ground Always Below 1 Ω
C54-64 (PTCR) - C54-53 (E1) Thermostat heater operation signal Ignition switch ON 11 to 14 V
C54-65 (PRG) - C54-53 (E1) Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 12)
C54-66 (ACIS) - C54-53 (E1) No. 1 vacuum switching valve assembly (for intake air control valve sub-assembly) operation signal Ignition switch ON 11 to 14 V
C54-69 (IGT5) - C54-53 (E1) No. 5 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C54-70 (IGT3) - C54-53 (E1) No. 3 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C54-71 (IGT1) - C54-53 (E1) No. 1 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C54-82 (KNK1) - C54-81 (EKNK) Knock control sensor (bank 1) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 13)
C54-87 (PR) - C54-133 (ETHW) Fuel pressure sensor (for high pressure side) signal Idling with warm engine 0.5 to 4.5 V
C54-89 (VTA2) - C54-120 (ETA) Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Accelerator pedal fully depressed (engine running) 4.6 to 5.0 V
C54-90 (VC) - C54-53 (E1) Power source for sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C54-91 (OX2B) - C54-92 (EX2B) Heated oxygen sensor (bank 2 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 14)
C54-93 (OX1B) - C54-94 (EX1B) Heated oxygen sensor (bank 1 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 14)
C54-96 (VCNE) - C54-53 (E1) Power source of crankshaft position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C54-98 (VCV2) - C54-97 (VV2-) Power source of VVT sensor (bank 2) (specific voltage) Ignition switch ON 4.5 to 5.5 V
C54-99 (VCV1) - C54-100 (VV1-) Power source of VVT sensor (bank 1) (specific voltage) Ignition switch ON 4.5 to 5.5 V
C54-101 (THW) - C54-133 (ETHW) Engine coolant temperature sensor Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C54-102 (THA) - C54-115 (E2G) Intake air temperature sensor Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C54-105 (SNWI) - C54-53 (E1) SNOW mode switch signal Ignition switch ON 11 to 14 V
Ignition switch ON, SNOW mode switch being pushed and held Below 1.5 V
C54-106 (NSW) - C54-53 (E1) Park/Neutral position switch assembly signal Ignition switch ON, shift lever not in P or N 11 to 14 V
Ignition switch ON, shift lever in P or N Below 1 V
C54-107 (R) - C54-53 (E1) R shift position switch signal Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1 V
C54-108 (P) - C54-53 (E1) P shift position switch signal Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
C54-114 (KNK2) - C54-113 (EKN2) Knock control sensor (bank 2) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 13)
C54-116 (VG) - C54-115 (E2G) Mass air flow meter sub-assembly signal Ignition switch ON Pulse generation
(See waveform 15)
C54-121 (VCTA) - C54-120 (ETA) Power source of throttle position sensor (specific voltage) Engine stopped, ignition switch ON 4.5 to 5.5 V
C54-122 (VTA1) - C54-120 (ETA) Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.1 V
Accelerator pedal fully depressed (engine running) 3.2 to 4.8 V
C54-123 (A2A+) - C54-53 (E1) Air fuel ratio sensor (bank 2 sensor 1) signal Ignition switch ON 3.3 V*
C54-124 (A2A-) - C54-53 (E1) Air fuel ratio sensor (bank 2 sensor 1) signal Ignition switch ON 2.9 V*
C54-125 (A1A+) - C54-53 (E1) Air fuel ratio sensor (bank 1 sensor 1) signal Ignition switch ON 3.3 V*
C54-126 (A1A-) - C54-53 (E1) Air fuel ratio sensor (bank 1 sensor 1) signal Ignition switch ON 2.9 V*
C54-127 (GE01) - Body ground Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω
C54-128 (NE+) - C54-95 (NE-) Crankshaft position sensor Idling with warm engine Pulse generation
(See waveform 16)
C54-129 (VV2+) - C54-97 (VV2-) VVT sensor (for intake camshaft of bank 2) signal Idling Pulse generation
(See waveform 17)
C54-130 (EV2+) - C54-97 (VV2-) VVT sensor (for exhaust camshaft of bank 2) signal Idling Pulse generation
(See waveform 18)
C54-131 (EV1+) - C54-100 (VV1-) VVT sensor (for exhaust camshaft of bank 1) signal Idling Pulse generation
(See waveform 18)
C54-132 (VV1+) - C54-100 (VV1-) VVT sensor (for intake camshaft of bank 1) signal Idling Pulse generation
(See waveform 17)
C54-134 (PFL) - C54-133 (ETHW) Fuel pressure sensor (for low pressure side) signal Idling with warm engine 0.75 to 4.5 V
C54-136 (RFC) - C54-53 (E1) Cooling fan control signal Ignition switch ON, A/C switch on (max cool) Pulse generation
(See waveform 19)
C54-139 (D) - C54-53 (E1) D shift position switch signal Ignition switch ON and shift lever in D or M 11 to 14 V
Ignition switch ON and shift lever not in D or M Below 1 V
C54-140 (N) - C54-53 (E1) N shift position switch signal Ignition switch ON, shift lever in N 11 to 14 V
Ignition switch ON, shift lever not in N Below 1 V

*: The ECM terminal voltage is constant regardless of the voltage output from the sensor.

WAVEFORM 1


A283576E13
3.01,1.396 3.344,1.708 0.333,0.313 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A283577E11
3.01,1.365 3.375,1.604 0.365,0.24 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A287796E34
2.604,1.635 3.063,1.833 0.458,0.198 10 false GND

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 1 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A283573E21
2.833,1.229 3.25,1.531 0.417,0.302 10 false GND

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 5


A283575E17
0.51,1.125 1.021,1.385 0.51,0.26 10 false GND

Cam Timing Oil Control Solenoid Assembly (for Exhaust Camshaft) Signal
ECM Terminal Name Between OE1+ and OE1-
Between OE2+ and OE2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 6


A283575E18
0.51,1.125 1.021,1.385 0.51,0.26 10 false GND

Cam Timing Oil Control Solenoid Assembly (for Intake Camshaft) Signal
ECM Terminal Name Between OC1+ and OC1-
Between OC2+ and OC2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 7


A205412E41
2.688,0.896 3.104,1.24 0.417,0.344 10 false GND

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Between HA2A and E05
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling


WAVEFORM 8


A408366E05
2.948,0.969 3.302,1.219 0.354,0.25 10 false GND

Ignition Coil Assembly Signal (IGT Signal)
ECM Terminal Name CH1: Between IGT (1 to 6) and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


WAVEFORM 9


A287799E22
0.656,1.583 1.115,1.781 0.458,0.198 10 false GND

No. 1 (to No. 6) Fuel Injector Assembly (for Port Injection) Signal
ECM Terminal Name Between #10 (to #60) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Port"

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

When the port injection injectors are operating, Port is displayed for Injection Way of the Data List.




WAVEFORM 10


A245848E77
2.854,1 3.323,1.354 0.469,0.354 10 false GND 0.479,0.625 0.844,0.875 0.365,0.25 10 false M-

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 11


A208000E82
2.854,0.99 3.313,1.302 0.458,0.313 10 false GND 0.469,0.656 0.938,0.948 0.469,0.292 10 false M+

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 12


A218020E38
2.802,0.938 3.292,1.26 0.49,0.323 10 false GND

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 13


A283572E33
2.615,1 3.115,1.292 0.5,0.292 10 false GND

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Between KNK2 and EKN2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed will differ slightly depending on the vehicle.




WAVEFORM 14


A283571E13
0.563,1.479 1.01,1.76 0.448,0.281 10 false GND

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Between OX2B and EX2B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

Data List, item "O2 Sensor Voltage B1S2" and "O2 Sensor Voltage B2S2" shows the ECM values from the heated oxygen sensor.



WAVEFORM 15


A337204E15
0.156,1.427 0.51,1.625 0.354,0.198 10 false GND

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and E2G
Tester Range 1 V/DIV., 100 μs./DIV.
Condition Ignition switch ON


WAVEFORM 16


A200774E35
2.969,1.177 3.396,1.438 0.427,0.26 10 false GND

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 17


A356009E12
0.135,1.344 0.521,1.563 0.385,0.219 10 false CH1 0.135,2.063 0.469,2.271 0.333,0.208 10 false CH2 2.813,1.469 3.271,1.667 0.458,0.198 10 false GND 2.802,2.198 3.26,2.396 0.458,0.198 10 false GND

VVT Sensor (for Intake Camshaft) Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 18


A356008E12
0.115,1.406 0.458,1.615 0.344,0.208 10 false CH1 0.115,2.094 0.458,2.302 0.344,0.208 10 false CH2 2.802,1.458 3.26,1.656 0.458,0.198 10 false GND 2.802,2.198 3.26,2.396 0.458,0.198 10 false GND

VVT Sensor (for Exhaust Camshaft) Signal
ECM Terminal Name CH1: Between EV1+ and VV1-
CH2: Between EV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 19


A282867E23
2.771,1.552 3.125,1.781 0.354,0.229 10 false GND

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.