Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM37A0E _51 Engine / Hybrid System _086849 2GR-FKS ENGINE CONTROL _0418696 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM.

The output signal from the MREL terminal of the ECM causes a current to flow to the coil of the EFI-MAIN relay, closing the contacts and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A422107E03
2.052,0.563 2.667,0.76 0.615,0.198 10 false IG1D 2.448,0.438 2.76,0.635 0.313,0.198 10 false 17 1.042,0.969 1.5,1.167 0.458,0.198 10 false H48 1.042,1.125 2.594,1.781 1.552,0.656 10 false Certification ECU (Smart Key ECU Assembly) 0.406,3.063 1.479,3.26 1.073,0.198 10 false FL MAIN 0.563,4.385 1.635,4.583 1.073,0.198 10 false Battery 1.948,2.146 3.177,2.344 1.229,0.198 10 false IG2-MAIN 2,3.385 2.646,3.917 0.646,0.531 10 false EFI-MAIN 3.073,2.583 4.448,2.781 1.375,0.198 10 false IG2 NO. 1 3.083,3.896 4.26,4.438 1.177,0.542 10 false EFI-MAIN 2.948,3.125 3.104,3.323 0.156,0.198 10 false 3 3.688,1.875 3.844,2.073 0.156,0.198 10 false 5 3.667,3.552 3.823,3.75 0.156,0.198 10 false 1 3.688,2.208 3.844,2.406 0.156,0.198 10 false 1 3.677,3.115 3.833,3.313 0.156,0.198 10 false 5 2.958,1.875 3.115,2.073 0.156,0.198 10 false 3 2.948,3.552 3.104,3.75 0.156,0.198 10 false 2 2.948,2.208 3.104,2.406 0.156,0.198 10 false 2 4.604,3.5 4.76,3.698 0.156,0.198 10 false 1 4.969,3.5 5.125,3.698 0.156,0.198 10 false 2 4.563,3.76 5.938,3.958 1.375,0.198 10 false EFI NO. 4 4.563,2.135 5.156,2.573 0.594,0.438 10 false ECU-IG2 NO. 1 5.833,4.229 6.292,4.427 0.458,0.198 10 false A28 5.833,1.99 6.292,2.188 0.458,0.198 10 false A28 5.833,2.854 6.292,3.052 0.458,0.198 10 false A28 5.833,3.229 6.292,3.427 0.458,0.198 10 false A28 5.823,4.656 6.281,4.854 0.458,0.198 10 false C54 5.885,1.792 6.042,1.99 0.156,0.198 10 false 4 5.896,2.656 6.052,2.854 0.156,0.198 10 false 2 5.896,3.042 6.052,3.24 0.156,0.198 10 false 3 5.854,4.031 6.167,4.229 0.313,0.198 10 false 46 5.854,4.469 6.167,4.667 0.313,0.198 10 false 53 6.167,1.875 6.781,2.073 0.615,0.198 10 false IGSW 6.156,2.833 6.469,3.031 0.313,0.198 10 false +B 6.156,3.208 6.615,3.406 0.458,0.198 10 false +B2 6.156,4.115 6.771,4.313 0.615,0.198 10 false MREL 6.167,4.656 6.479,4.854 0.313,0.198 10 false E1 6.427,5.177 6.885,5.375 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-53 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)
a.
A371640C33
1.583,0.76 1.958,0.979 0.375,0.219 1.26,2.677 1.563,1.552 true 0.292,0.354 0.604,0.552 0.313,0.198 10 false *a 1.104,2.708 1.719,2.906 0.615,0.198 10 false IGSW 1.646,0.792 2.26,0.99 0.615,0.198 10 false A28
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-4 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI-MAIN RELAY

NG

7.INSPECT IG2 NO. 1 RELAY
3.INSPECT EFI-MAIN RELAY

OK

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - ECM)

NG

REPLACE EFI-MAIN RELAY

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - ECM)
a.

Remove the EFI-MAIN relay, FUEL PMP relay and A/F HTR relay from the No. 1 engine room relay block and No. 1 junction block assembly.

HINT:

Remove the FUEL PMP and A/F HTR relays connected between the checked terminals as the coil inside the relay influences the measurement value.



b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN relay) - A28-46 (MREL) Always Below 1 Ω
5 (EFI-MAIN relay) - A28-2 (+B) Always Below 1 Ω
5 (EFI-MAIN relay) - A28-3 (+B2) Always Below 1 Ω
2 (EFI-MAIN relay) or A28-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher
5 (EFI-MAIN relay) or A28-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (EFI-MAIN relay) or A28-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN RELAY)
A457147C01
0.063,0.063 0.375,0.26 0.313,0.198 10 false *1 0.344,1.604 0.656,1.802 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 EFI-MAIN Relay


a.

Remove the EFI-MAIN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN RELAY)

6.CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - BODY GROUND)
a.

Remove the EFI-MAIN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IG2 NO. 1 RELAY

OK

8.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM)

NG

REPLACE IG2 NO. 1 RELAY

8.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IG2 NO. 1 relay) - A28-4 (IGSW) Always Below 1 Ω
5 (IG2 NO. 1 relay) or A28-4 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY)
A457148C01
0.052,0.063 0.365,0.26 0.313,0.198 10 false *1 0.344,1.865 0.656,2.063 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 IG2 NO. 1 Relay


a.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IG2 NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IG2 NO. 1 RELAY)

10.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND)
a.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IG2 NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the instrument panel junction block assembly 4B connector.

HINT:

Disconnect the IG1-NO. 1, IG1-NO. 2 and IG2-NO. 2 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-17 (IG1D) - 1 (IG2 NO. 1 relay) Always Below 1 Ω
H48-17 (IG1D) or 1 (IG2 NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR