Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display)
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter  


DESCRIPTION

The navigation ECU receives a vehicle speed signal from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E419027E21
1.542,0.271 2.688,0.531 1.146,0.26 10 false to Other Systems 2.115,1.417 2.427,1.615 0.313,0.198 10 false +S 2.427,1.292 2.74,1.49 0.313,0.198 10 false 6 4.615,1.313 4.927,1.51 0.313,0.198 10 false 9 4.833,1.427 5.281,1.646 0.448,0.219 10 false SPD 4.813,2.104 5.292,2.313 0.479,0.208 10 false H18 4.802,2.26 6,2.51 1.198,0.25 10 false Navigation ECU 1.01,2.073 1.781,2.271 0.771,0.198 10 false H21 1.01,2.24 2.979,2.594 1.969,0.354 10 false Combination Meter Assembly

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E393685C46
1.49,0.344 1.917,0.615 0.427,0.271 2.438,1.938 2.177,1.333 false 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 1.573,0.406 2.031,0.604 0.458,0.198 10 false H21 2.385,1.958 2.698,2.156 0.313,0.198 10 false +S 2.771,3.594 3.229,3.792 0.458,0.198 10 false GND 1.125,3.844 1.281,4.042 0.156,0.198 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal H21-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT NAVIGATION ECU (INPUT WAVEFORM)

NG

2.INSPECT NAVIGATION ECU (INPUT WAVEFORM)
a.
E401096C24
1.49,0.417 1.906,0.667 0.417,0.25 0.917,1.948 0.885,1.042 false 2.781,3.604 3.24,3.802 0.458,0.198 10 false GND 1.125,3.854 1.438,4.135 0.313,0.281 10 false A 0.854,1.969 1.208,2.25 0.354,0.281 10 false SPD 0.115,0.094 0.469,0.375 0.354,0.281 10 false *a 1.583,0.469 1.938,0.75 0.354,0.281 10 false H18
*a Component with harness connected
(Navigation ECU)


Check the input waveform.

i.

Remove the navigation ECU with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal H18-9 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H18-9 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR