Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) D

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  OPERATION CHECK  


CHECK CUSTOMIZE PARAMETERS


a.

The operation check below is based on the non-customized initial condition of the vehicle.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS



CHECK PUSH-BUTTON START FUNCTION


a.

Check the push-button start function:

i.

Get into the vehicle while carrying the electrical key transmitter sub-assembly with the ignition switch off. With the shift lever in P, check that the key indicator display is displayed when the brake pedal is depressed. Check that the hybrid control system starts when the power switch is pressed after the key indicator display is displayed on the multi-information display.


ii.

While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the power switch is pressed with the brake pedal released: off → ACC → ON → off.

HINT:

If the power switch is pressed with the ignition switch ON and the shift lever not in P, the power source mode will not change to off, but to ACC.



iii.

With the shift lever in P, check that the steering lock operates when a door is opened.


iv.
B560861C04
0.635,1.135 2.833,0.25 2.833,0.25 3,0.25 false 2.063,1.135 2.833,0.25 false 3.031,0.177 3.344,0.375 0.313,0.198 10 false *a
*a Inspection Point


Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>PARTS LOCATION

·

Perform this inspection for both inspection points.




v.
B560862C04
0.688,0.313 2.75,0.083 2.75,0.083 3,0.083 false 2.052,0.302 2.75,0.083 false 3.031,0.031 3.344,0.229 0.313,0.198 10 false *a
*a Inspection Point


Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>PARTS LOCATION

·

Perform this inspection for both inspection points.




vi.
B560864C02
1.365,1.698 2.583,0.167 2.583,0.167 2.833,0.167 false 1.948,1.333 2.583,0.167 false 2.885,0.083 3.198,0.281 0.313,0.198 10 false *a
*a Inspection Point


Check the push-button start function operation range for the luggage compartment. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 3 indoor electrical key antenna assembly (inside luggage compartment).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>PARTS LOCATION

·

Perform this inspection for both inspection points.






CHECK POWER SOURCE MODE CHANGING FUNCTION


a.

Check the power switch.

i.

Check that the power source mode changes according to the chart below.

Shift Position Brake Pedal Power Source Mode when Power Switch Pressed
P Released Off → ACC → ON → off
P Released ON (READY) → off
P Released ACC* → off
P Depressed Off → ON (READY)
P Depressed ACC → ON (READY)
P Depressed ON → ON (READY)
P Depressed ON (READY) → off
P Depressed ACC* → off
Not P Released Off → ACC → ON (after power source mode changes to ON, power source mode changes between ON and ACC every time power switch is pressed)
Not P Released ON (READY) → ACC
Not P Depressed Off → ON
Not P Depressed ACC → ON
Not P Depressed ON (READY) → ACC

HINT:

*: This situation is only applicable when the power source mode has changed from ON to ACC.





CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION


a.

Check the transmitter battery saving mode function:

i.

Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.


ii.

Check that the entry and start system does not operate while in transmitter battery saving mode.

HINT:

To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.





CHECK ENTRY CANCEL FUNCTION


a.

Disable the entry and start system and check that all functions of the entry and start system no longer operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS

HINT:

When the entry and start system is disabled, it is possible to lock and unlock the doors with the wireless function, and the hybrid control system can be started by holding the electrical key transmitter sub-assembly near the power switch.