Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG circuit or IG hold circuit of the certification ECU (smart key ECU assembly) is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2271 Ignition Hold Monitor Malfunction When either of the following conditions is met (1-trip detection logic*1):
·

The IG circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*2

·

The IG hold circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*3


·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Turn the ignition switch to ON.



*1: Only detected while a malfunction is present and the ignition switch is ON.

*2: The IG circuit and IG hold circuit activate the IG relay.

*3: After the IG circuit turns on, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit will maintain the power source mode in ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The ignition switch cannot be turned to ON (the hybrid control system cannot be started). The power source mode cannot be changed to ON.

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2271
Power Source Control
·

IG Relay Monitor (Inside)

·

Latch Circuit



WIRING DIAGRAM

B478612E25
1.271,1.01 2.656,1.281 1.385,0.271 10 false to each IG Relay 5.427,0.896 6.219,1.167 0.792,0.271 10 false 17 5.688,0.896 6.479,1.167 0.792,0.271 10 false IG1D 5.948,0.521 6.74,0.792 0.792,0.271 10 false +B 6.385,0.896 6.708,1.198 0.323,0.302 10 false IC 5.385,1.844 6.177,2.115 0.792,0.271 10 false H48 5.375,2.01 6.896,2.5 1.521,0.49 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B531739C06
1.542,0.083 1.958,0.333 0.417,0.25 1.292,1.958 1.177,1.958 1.177,1.958 1.177,0.958 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.625,0.115 2,0.323 0.375,0.208 10 false H48 1.323,1.875 1.823,2.115 0.5,0.24 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H48-17 (IG1D) - Body ground Ignition switch ACC → Ignition switch ON 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)