Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  B2278  Engine/Power Switch Malfunction  


DESCRIPTION

This DTC is stored when the SSW1 contact signal and SSW2 contact signal, which are detected when the power switch is operated, do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2278 Engine/Power Switch Malfunction When the power switch is operated, the SSW1 contact signal and SSW2 contact signal do not match (1-trip detection logic*).
·

Power switch

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Turn the ignition switch to ON.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
If either the SSW1 contact signal or SSW2 contact signal is stuck on, the power source mode cannot be changed by pressing the power switch. If either the SSW1 contact signal or SSW2 contact signal is stuck off, emergency stop by pressing and holding the power switch for 2 seconds or more cannot be operated. -

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2278
Power Source Control
·

Start Switch1

·

Start Switch2



WIRING DIAGRAM

B463081E24
4.99,3.01 6.51,3.417 1.521,0.406 10 false Certification ECU (Smart Key ECU Assembly) 5.552,0.458 6.333,0.75 0.781,0.292 10 false +B 6.01,1.323 6.792,1.615 0.781,0.292 10 false IC 4.99,2.854 5.625,3.24 0.635,0.385 10 false H48 5.146,0.927 5.927,1.219 0.781,0.292 10 false SSW1 5.146,1.573 5.927,1.865 0.781,0.292 10 false SSW2 5.146,2.188 5.927,2.479 0.781,0.292 10 false AGND 4.917,0.927 5.385,1.26 0.469,0.333 10 false 23 4.927,1.563 5.396,1.896 0.469,0.333 10 false 21 4.917,2.177 5.385,2.51 0.469,0.333 10 false 11 1.927,0.927 2.396,1.26 0.469,0.333 10 false 5 1.927,1.542 2.396,1.875 0.469,0.333 10 false 1 1.938,2.177 2.406,2.51 0.469,0.333 10 false 6 1.427,2.177 2.208,2.469 0.781,0.292 10 false AGND 1.542,1.552 2.323,1.844 0.781,0.292 10 false SS2 1.542,0.927 2.323,1.219 0.781,0.292 10 false SS1 0.917,2.854 1.552,3.24 0.635,0.385 10 false H50 0.917,3.01 2.438,3.417 1.521,0.406 10 false Power Switch

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine if the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
2.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

According to the display on the GTS, read the Data List while wiggling the wire harness.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine if the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H50 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-23 (SSW1) - H50-5 (SS1) Always Below 1 Ω
H48-21 (SSW2) - H50-1 (SS2) Always Below 1 Ω
H48-11 (AGND) - H50-6 (AGND) Always Below 1 Ω
H48-23 (SSW1) or H50-5 (SS1) - Other terminals and body ground Always 10 kΩ or higher
H48-21 (SSW2) or H50-1 (SS2) - Other terminals and body ground Always 10 kΩ or higher
H48-11 (AGND) or H50-6 (AGND) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT POWER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER SWITCH

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG