Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2284 Brake Signal Malfunction The brake signal sent via direct line and the brake signal sent via CAN communication do not match. (1-trip detection logic*)
·

Electronically controlled brake system

·

Stop light switch assembly

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Connect the cable to the negative (-) auxiliary battery terminal, release the brake pedal and wait at least 20 seconds. Then depress the brake pedal for 20 seconds or more.



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if a hybrid control system start operation is performed, the hybrid control system does not start (the key indicator display is not displayed on the multi-information display). However, the hybrid control system can be started by turning the ignition switch to ACC and then pressing and holding it.
·

If there is a malfunction when the brake signal sent via direct line is on, the hybrid control system can be started by pressing the power switch with the brake pedal released.

·

If there is a malfunction when the brake signal sent via direct line is off, the hybrid control system cannot be started by pressing the power switch with the brake pedal depressed.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2284
Power Source Control
·

Stop Light Switch1


Hybrid Control
·

Stop Light Switch



WIRING DIAGRAM

B572354E01
0.792,3.302 3.167,3.521 2.375,0.219 10 false : CAN Communication Line 0.333,0.833 0.958,1.052 0.625,0.219 10 false A31 0.323,1 2.042,1.49 1.719,0.49 10 false Hybrid Vehicle Control ECU 1.198,1.719 1.823,1.938 0.625,0.219 10 false L 1.417,1.719 2.042,1.938 0.625,0.219 10 false 3 5.49,2.625 6.115,2.844 0.625,0.219 10 false M5 5.49,2.792 7.01,3.302 1.521,0.51 10 false Certification ECU (Smart Key ECU Assembly) 5.552,1.719 6.177,1.938 0.625,0.219 10 false 25 5.844,1.719 6.469,1.938 0.625,0.219 10 false STP1 3.771,1 5.667,1.469 1.896,0.469 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 1.417,0.354 2.042,0.573 0.625,0.219 10 false 7 4.083,0.479 4.708,0.698 0.625,0.219 10 false STP2 6.469,1.948 6.792,2.188 0.323,0.24 10 false IC 3.781,0.833 5.167,1.177 1.385,0.344 10 false A57 3.823,0.354 4.448,0.573 0.625,0.219 10 false 37 1.021,0.479 1.646,0.698 0.625,0.219 10 false STP 0.865,1.823 1.188,2.063 0.323,0.24 10 false IC 0.333,2.219 0.958,2.438 0.625,0.219 10 false A42 0.323,2.385 2.167,2.729 1.844,0.344 10 false Stop Light Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A42 stop light switch assembly connector.


c.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the A31 hybrid vehicle control ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-25 (STP1) - A42-3 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the M5 certification ECU (smart key ECU assembly) connector.


b.

Connect the A42 stop light switch assembly connector.


c.
B427582C28
1.479,0.167 1.865,0.406 0.385,0.24 1.135,2 1.344,2 1.344,2 1.344,1.167 true 0.156,0.156 0.469,0.313 0.313,0.156 10 false *a 1.573,0.198 1.885,0.354 0.313,0.156 10 false M5 0.75,1.917 1.188,2.104 0.438,0.188 10 false STP1
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M5-25 (STP1) - Body ground Brake pedal released → depressed 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY