Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  B228B  System Voltage or GND Energization Malfunction  


DESCRIPTION

This DTC is stored when there is a malfunction in the certification ECU (smart key ECU assembly) auxiliary battery power supply circuit or ground circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B228B System Voltage or GND Energization Malfunction A malfunction is detected in the certification ECU (smart key ECU assembly) auxiliary battery power supply circuit or ground circuit. (1-trip detection logic*)
·

AM2 fuse

·

Wire harness or connector


DTC Output Confirmation Operation:

Drive the vehicle.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The hybrid control system stopped while driving. -

Related Data List and Active Test Items
DTC No. Data List and Active Test
B228B -

WIRING DIAGRAM

B463086E27
1.51,0.458 3.344,0.656 1.833,0.198 10 false from Auxiliary Battery 4.438,0.635 5.042,1.073 0.604,0.438 10 false AM2 5.688,0.479 6.292,0.917 0.604,0.438 10 false +B 5.688,1.281 6.292,1.719 0.604,0.438 10 false E 5.51,0.385 6.115,0.823 0.604,0.438 10 false 4 5.427,1.188 6.031,1.625 0.604,0.438 10 false 18 5.427,1.979 6.938,2.354 1.51,0.375 10 false Certification ECU (Smart Key ECU Assembly) 5.438,1.833 6.354,2.063 0.917,0.229 10 false H48

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B518918C40
1.448,2.427 1.865,2.677 0.417,0.25 2.521,4.385 2.271,4.385 2.271,4.385 2.271,3.552 true 0.406,3.031 0.719,3.188 0.313,0.156 10 false *a 1.531,2.458 1.885,2.698 0.354,0.24 10 false H48 2.563,4.302 2.885,4.531 0.323,0.229 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H48-4 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B518918C41
1.469,2.427 1.885,2.677 0.417,0.25 1.406,4.375 1.156,4.375 1.156,4.375 1.156,3.792 true 0.333,2.917 0.625,3.115 0.292,0.198 10 false *a 1.552,2.458 2,2.76 0.448,0.302 10 false H48 1.458,4.292 1.615,4.49 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-18 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE