Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to ON but does change to ACC
Power Source Control
·

Power Supply Condition

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

IG Circuit



WIRING DIAGRAM

B477750E02
0.688,3.771 2.208,4.146 1.521,0.375 10 false Certification ECU (Smart Key ECU Assembly) 1.219,0.573 1.417,0.781 0.198,0.208 10 false IC 1.573,0.229 2.167,0.729 0.594,0.5 10 false +B 1.708,0.594 2.302,1.094 0.594,0.5 10 false IG1D 2.125,0.594 2.406,0.833 0.281,0.24 10 false 17 0.698,3.604 1.208,3.885 0.51,0.281 10 false H48 3.563,3.604 6.344,4 2.781,0.396 10 false Instrument Panel Junction Block Assembly 3.438,0.698 4.01,1.063 0.573,0.365 10 false 4A 3.458,0.5 3.74,0.74 0.281,0.24 10 false 17 3.448,1.49 4.021,1.854 0.573,0.365 10 false 4F 3.479,1.292 3.76,1.531 0.281,0.24 10 false 1 4.396,0.99 5.271,1.25 0.875,0.26 10 false IG1-NO. 1 4.396,2.021 5.271,2.281 0.875,0.26 10 false IG1-NO. 2 4.385,3.042 5.26,3.302 0.875,0.26 10 false IG2-NO. 2 5.042,0.583 6.396,1.052 1.354,0.469 10 false ECU-IG1 NO. 1 5.219,1.625 6.573,2.094 1.354,0.469 10 false WIPER RR 5.01,2.656 6.365,3.125 1.354,0.469 10 false ECU-IG2 NO. 3 6.177,0.448 6.75,0.813 0.573,0.365 10 false 4C 6.188,0.25 6.469,0.49 0.281,0.24 10 false 14 3.448,2.51 4.021,2.875 0.573,0.365 10 false 4E 3.479,2.302 3.76,2.542 0.281,0.24 10 false 1 3.448,3.26 4.021,3.625 0.573,0.365 10 false 4B 3.479,3.052 3.76,3.292 0.281,0.24 10 false 3 6.177,1.49 6.75,1.854 0.573,0.365 10 false 4D 6.188,1.281 6.469,1.521 0.281,0.24 10 false 12 6.188,2.51 6.76,2.875 0.573,0.365 10 false 4C 6.177,2.323 6.458,2.563 0.281,0.24 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B531739C04
1.542,0.083 1.958,0.333 0.417,0.25 0.927,1.979 1.177,1.979 1.177,1.979 1.177,0.979 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.625,0.115 1.979,0.375 0.354,0.26 10 false H48 0.583,1.896 1.083,2.135 0.5,0.24 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H48-17 (IG1D) - Body ground Ignition switch off → Ignition switch ACC 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 4A, 4B, 4E and 4F instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-17 (IG1D) - 4A-17 Always Below 1 Ω
4B-3 - Body ground Always Below 1 Ω
H48-17 (IG1D) or 4A-17 - Other terminals and body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4E-1 - Body ground Ignition switch off 11 to 14 V
4F-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG1-NO. 2, IG2-NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG1-NO. 2, IG2-NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect all of the instrument panel junction block assembly connectors.


c.

Connect the H48 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

B463118C96
2.26,2.333 2.573,2.542 0.313,0.208 3.698,2.333 4.01,2.542 0.313,0.208 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 2.344,2.354 2.656,2.51 0.313,0.156 10 false 4D 3.771,2.354 4.083,2.51 0.313,0.156 10 false 4C
*a Component with harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
4C-14 - Body ground Ignition switch ON 11 to 14 V
4D-12 - Body ground Ignition switch ON 11 to 14 V
4C-15 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY