Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Power Source Mode does not Change to ON (ACC)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to ACC but does change to ON
Power Source Control
·

Power Supply Condition

·

ACC Relay Monitor



WIRING DIAGRAM

B477751E02
0.688,1.844 2.208,2.313 1.521,0.469 10 false Certification ECU (Smart Key ECU Assembly) 0.688,1.688 1.313,1.906 0.625,0.219 10 false H48 1.146,1.219 1.771,1.438 0.625,0.219 10 false IC 1.521,0.875 2.146,1.094 0.625,0.219 10 false +B 1.583,1.198 2.208,1.417 0.625,0.219 10 false ACCD 2.052,1.25 2.375,1.521 0.323,0.271 10 false 16 3.375,1.344 3.698,1.615 0.323,0.271 10 false 4A 3.396,1.135 3.719,1.406 0.323,0.271 10 false 30 3.375,0.813 3.698,1.083 0.323,0.271 10 false 4B 3.427,0.604 3.75,0.875 0.323,0.271 10 false 3 3.385,0.365 3.708,0.635 0.323,0.271 10 false 4F 3.417,0.156 3.74,0.427 0.323,0.271 10 false 1 4.49,1.104 4.813,1.375 0.323,0.271 10 false ACC 5.167,0.51 5.958,0.885 0.792,0.375 10 false ECU-ACC 6.104,0.365 6.427,0.635 0.323,0.271 10 false 4A 6.115,0.146 6.438,0.417 0.323,0.271 10 false 40 3.552,1.729 6.448,2.219 2.896,0.49 10 false Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B531739C05
1.542,0.083 1.958,0.333 0.417,0.25 1.052,1.969 1.302,1.969 1.302,1.969 1.302,0.969 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.635,0.115 1.99,0.375 0.354,0.26 10 false H48 0.635,1.875 1.135,2.115 0.5,0.24 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H48-16 (ACCD) - Body ground Ignition switch ACC → Ignition switch ON 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 4A, 4B and 4F instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-16 (ACCD) - 4A-30 Always Below 1 Ω
4B-3 - Body ground Always Below 1 Ω
H48-16 (ACCD) or 4A-30 - Other terminals and body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4F-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect all of the instrument panel junction block assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

B570698C01
3.052,1.51 3.333,1.729 0.281,0.219 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 3.104,1.531 3.417,1.729 0.313,0.198 10 false 4A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
4A-40 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY