If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.
| Problem Symptom | Data List and Active Test |
|---|---|
| Power source mode does not change to ACC but does change to ON | Power Source Control
·
Power Supply Condition ·
ACC Relay Monitor Starting Control
·
Ignition |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After completing repairs, confirm that the problem does not recur.
After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Entry and start system (for Start Function) DTCs are output | B |
A
B
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H48-16 (ACCD) - Body ground | Ignition switch ACC → Ignition switch ON | 1 V or less → 9 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
Disconnect the 4A, 4B and 4F instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H48-16 (ACCD) - 4A-30 | Always | Below 1 Ω |
| 4B-3 - Body ground | Always | Below 1 Ω |
| H48-16 (ACCD) or 4A-30 - Other terminals and body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4F-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Connect all of the instrument panel junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4A-40 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG