The certification ECU (smart key ECU assembly) blinks the security indicator light (telltale light assembly) when the immobiliser is set (ignition switch off).
The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light (telltale light assembly).
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.
Check for DTCs.
DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Immobiliser Indicator | Security indicator light | OFF/ON | - |
| Tester Display |
|---|
| Immobiliser Indicator |
The security indicator light (radio receiver assembly) operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When the immobiliser is set, check that the security indicator light (telltale light assembly) blinks.*1
The security indicator light (telltale light assembly) blinks normally.
When the theft deterrent system is in the arming preparation state, check that the security indicator light (telltale light assembly) illuminates.*2
The security indicator light (telltale light assembly) illuminates normally.
| Result | Proceed to |
|---|---|
| *1 is NG (*2 is OK) | A |
| *2 is NG (*1 is OK) | B |
A
B
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
Disconnect the H33 security indicator light (telltale light assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H48-20 (IND) - H33-3 (LP) | Always | Below 1 Ω |
| H48-20 (IND) or H33-3 (LP) - Other terminals and body ground | Always | 10 kΩ or higher |
| H33-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H48 certification ECU (smart key ECU assembly) connector.
Connect the H33 security indicator light (telltale light assembly) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H48-20 (IND) - Body ground | Ignition switch off → ON | Pulse generation → Below 2 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL
NG