Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2020.02–2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  CALIBRATION  


ADJUST PANORAMIC VIEW MONITOR SYSTEM


a.

This panoramic view monitor system can be set from the diagnostic screen of the radio and display receiver assembly.


b.

If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

Part Name Operation Adjustment Item Proceed to

*: When "!" is displayed on the panoramic view monitor screen, perform steering sensor zero point calibration.

Steering sensor
·

Removal and installation of the steering sensor

·

Removal and installation of the connector of the steering sensor

·

Replacement


Steering angle neutral point (Initialize panoramic view monitor system)* (Click here)
Adjust steering angle Procedure 9
Parking assist ECU Replacement Parking assist ECU initialization Procedure 2
Procedure 7
Procedure 8
Adjust steering angle Procedure 9
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Parking assist ECU initialization Procedure 2
Procedure 7
Procedure 8
Adjust steering angle Procedure 9
Rear television camera assembly
·

Replacement

·

Installation angle of the rear television camera changes because of the removal and installation of the rear television camera, etc.


Rear television camera view adjustment Procedure 2
Procedure 4
Procedure 8
·

Front television camera assembly

·

Front bumper assembly

·

Radiator grille sub-assembly


·

Replacement

·

Installation angle of the front television camera changes because of the removal and installation of the front television camera, etc.


Front television camera view adjustment Procedure 2
Procedure 3
Procedure 8
·

Side television camera assembly LH

·

Outer rear view mirror assembly LH


·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera view adjustment Procedure 2
Procedure 5
Procedure 8
·

Side television camera assembly RH

·

Outer rear view mirror assembly RH


·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera view adjustment Procedure 2
Procedure 6
Procedure 8
·

Front television camera assembly, front bumper assembly or radiator grille sub-assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Replacement or removal and installation of 2 or more parts Television camera view adjustment Procedure 2
Procedure 7
Procedure 8

HINT:

The adjustment values stored while performing panoramic view monitor system calibration are stored in the parking assist ECU.




PROCEDURE 1: PRE-WORK CHECKS


a.

Preliminary checks

NOTICE:
·

Provide shadow to prevent back-up light from hitting the camera.

·

Use string that does not stretch.

·

Apply pieces of adhesive tape to serve as check markers. When placing the markers, make them 100 mm (3.94 in.) wide.



i.

Perform the work at a wide, level location (There is approximately 2000 mm [6.56 ft.] all around the vehicle).


ii.

Park the vehicle on a flat surface with the steering wheel centered.

NOTICE:

Before stopping the vehicle, move the vehicle backward and forward to ensure that both the steering wheel and the tires point straight ahead.



iii.

Adjust the tire pressure to the specified value(s).


iv.

Remove all luggage from the vehicle before starting work.



b.

Marker locations

i.

Secure the string to the locations required to make the checks and set markers as shown in the illustration.

·
E287135C01
0.479,0.698 0.844,1.146 false 2.229,0.469 1.844,1.115 false 2.302,1.333 2.552,1.708 false 1.104,1.333 0.854,1.74 false 2.01,4.052 1.708,3.688 false 2.573,3.49 2.271,3.083 false 0.292,0.583 0.75,0.781 0.458,0.198 10 false *e 2.302,0.396 3.188,0.677 0.885,0.281 10 false *b 0.729,1.76 0.948,2 0.219,0.24 10 false *a 2.063,4 2.521,4.198 0.458,0.198 10 false *d 2.615,3.5 3.073,3.698 0.458,0.198 10 false *c 2.531,1.75 2.75,1.99 0.219,0.24 10 false *a
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3


Front camera adjustment only

·
E287136C01
1.719,1.042 2.073,0.563 false 2.552,3.135 2.781,2.729 false 2.375,3.823 2.5,4.01 false 0.958,3.823 0.708,4.094 false 1.521,3.813 1.521,4.292 false 0.552,3.49 0.76,3.792 false 2.146,0.469 2.604,0.667 0.458,0.198 10 false *d 0.385,3.406 0.844,3.604 0.458,0.198 10 false *e 0.563,4.094 1.25,4.458 0.688,0.365 10 false *a 2.458,4.042 3.146,4.406 0.688,0.365 10 false *a 1.427,4.344 2.365,4.552 0.938,0.208 10 false *b 2.823,2.635 3.323,2.854 0.5,0.219 10 false *c
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 4


Rear camera adjustment only

·
E287137C01
1.063,0.917 0.688,0.563 false 2.281,0.958 2.688,0.656 false 2.271,2.906 2.625,2.646 false 2.375,3.521 2.688,3.313 false 1.719,3.635 1.927,3.875 false 1.125,3.542 1.49,4.125 false 1.094,3.833 0.844,4.083 false 1.073,1.542 0.771,1.365 false 1.052,2.25 0.781,2.375 false 0.531,0.458 1.24,0.833 0.708,0.375 10 false *a 1.469,4.167 1.698,4.406 0.229,0.24 10 false *a 0.594,1.281 0.969,1.573 0.375,0.292 10 false *b 0.708,4.083 1.156,4.333 0.448,0.25 10 false *g 1.958,3.844 2.406,4.094 0.448,0.25 10 false *d 2.667,2.563 3.115,2.813 0.448,0.25 10 false *c 2.74,3.24 3.188,3.49 0.448,0.25 10 false *f 2.719,0.583 3.167,0.833 0.448,0.25 10 false *e 0.604,2.323 0.979,2.615 0.375,0.292 10 false *b
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3
*f String 4
*g String 5


Left camera adjustment only

·
E287138C01
0.573,0.438 0.854,0.906 false 2.615,0.563 2.344,0.854 false 2.594,3.781 2.313,3.74 false 2.271,3.521 1.844,4.188 false 1.708,3.615 1.365,3.844 false 0.969,3.479 0.75,3.229 false 0.885,2.865 0.667,2.615 false 2.615,1.188 2.344,1.479 false 2.677,2.427 2.344,2.167 false 2.646,0.5 3.344,0.844 0.698,0.344 10 false *a 1.74,4.188 2.104,4.448 0.365,0.26 10 false *a 2.635,1.094 2.979,1.385 0.344,0.292 10 false *b 0.406,0.323 0.792,0.542 0.385,0.219 10 false *e 0.51,2.49 0.896,2.708 0.385,0.219 10 false *c 0.594,3.125 0.979,3.344 0.385,0.219 10 false *f 1.188,3.792 1.573,4.01 0.385,0.219 10 false *d 2.635,3.729 3.021,3.948 0.385,0.219 10 false *g 2.708,2.427 3.052,2.719 0.344,0.292 10 false *b
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3
*f String 4
*g String 6


Right camera adjustment only

·

Adjustment of 4 cameras

E287104C01
4.833,3.344 5.083,3 false 2.417,1.5 2.875,1.5 false 4.26,1.5 4.75,1.5 false 3.25,4.469 3.573,4.135 false 3.917,4.469 3.792,4.073 false 5,4.031 5.25,4.344 false 5,1.115 5.25,0.833 false 4.292,1.073 5,0.417 false 2.823,1.083 2.406,0.667 false 3.667,1.083 3.844,0.76 false 4.302,1.771 4.823,1.771 false 4.302,2.552 4.823,2.552 false 4.292,4.094 4.542,4.406 false 2.5,4.417 2.823,4.083 false 2.313,1.792 2.833,1.792 false 2.313,2.552 2.833,2.552 false 2.219,0.521 2.51,0.75 0.292,0.229 10 false *a 5.052,0.333 6.302,0.5 1.25,0.167 10 false *a 4.875,1.698 5.708,1.865 0.833,0.167 10 false *b 3.865,4.5 4.115,4.719 0.25,0.219 10 false *b 3.854,0.646 4.083,0.896 0.229,0.25 10 false *b 2.25,1.438 2.667,1.604 0.417,0.167 10 false *g 4.802,1.417 5.219,1.583 0.417,0.167 10 false *h 5.135,2.917 5.552,3.083 0.417,0.167 10 false *c 5.302,0.75 5.719,0.917 0.417,0.167 10 false *e 5.229,4.385 5.646,4.552 0.417,0.167 10 false *f 3.063,4.5 3.479,4.667 0.417,0.167 10 false *d 4.865,2.479 5.698,2.646 0.833,0.167 10 false *b 4.531,4.448 4.948,4.615 0.417,0.167 10 false *a 2.365,4.406 2.781,4.573 0.417,0.167 10 false *a 2.125,1.719 2.958,1.885 0.833,0.167 10 false *b 2.125,2.458 2.958,2.625 0.833,0.167 10 false *b
*a Cross Check Marker *b Check Marker
*c String 1 *d String 2
*e String 3 *f String 4
*g String 5 *h String 6





c.

Marker positions

i.

Set the check markers at the positions shown in the illustration.

E287105C01
1.594,2.135 1.594,1.938 1.594,1.938 1.927,1.938 false 1.594,4.073 1.594,3.875 1.594,3.875 1.927,3.875 false 3.76,0.5 3.76,0.198 3.76,0.198 4.094,0.198 false 4.927,3.281 4.927,3.125 4.927,3.125 4.646,3.125 false 3.385,0.5 3.385,0.198 3.385,0.198 3.073,0.198 false 5.5,3.073 5.5,2.917 5.5,2.917 5.219,2.917 false 6.073,2.75 6.073,2.594 6.073,2.594 5.792,2.594 false 6.656,2.531 6.656,2.375 6.656,2.375 6.375,2.375 false 3.313,5.094 3.406,4.99 false 3.167,5.458 3.24,5.333 false 3.802,5.104 3.729,4.99 false 4,5.469 3.927,5.333 false 1.51,2.167 1.823,2.365 0.313,0.198 10 false *a 1.531,4.104 1.844,4.302 0.313,0.198 10 false *b 3.073,5.479 3.385,5.677 0.313,0.198 10 false *c 3.938,5.479 4.25,5.677 0.313,0.198 10 false *c 4.865,3.302 5.177,3.5 0.313,0.198 10 false *e 6,2.76 6.313,2.958 0.313,0.198 10 false *g 6.583,2.573 6.896,2.771 0.313,0.198 10 false *h 4.135,0.125 4.448,0.323 0.313,0.198 10 false *d 3.208,5.125 3.521,5.323 0.313,0.198 10 false *d 2.885,0.135 3.198,0.333 0.313,0.198 10 false *d 3.74,5.125 4.052,5.323 0.313,0.198 10 false *d 5.438,3.115 5.75,3.313 0.313,0.198 10 false *f
*a 5000 mm (16.4 ft.) *b 1500 mm (4.92 ft.)
*c 1400 mm (4.59 ft.) *d 693 mm (2.27 ft.)
*e 1400 mm (4.59 ft.) *f 1600 mm (5.25 ft.)
*g 3100 mm (10.17 ft.) *h 3300 mm (10.82 ft.)





PROCEDURE 2: SET DATUM POINTS


a.

Extend the datum line (string 1).

i.
E432416C01
1.646,2.813 1.969,3.125 1.969,3.125 2.219,3.125 false 1.688,2.698 2.354,2.51 2.354,2.51 2.604,2.51 false 2.271,3.042 2.583,3.198 0.313,0.156 10 false *a 2.656,2.427 2.969,2.583 0.313,0.156 10 false *b
*a Mark A
*b Weight


Hang a weight with a pointed tip and accurately mark the center position on the road surface. (Mark A)

NOTICE:

Make sure that the weight hangs straight down from the string.



ii.

Repeat the procedure to mark the right side. (Mark B)


iii.
E287139C01
1.01,2.771 1.292,2.458 false 2.417,2.74 2.125,2.458 false 2.385,2.458 2.542,2.073 false 2.594,1.969 2.875,2.135 0.281,0.167 10 false *a 0.885,2.802 1.135,2.938 0.25,0.135 10 false *b 2.385,2.792 2.646,2.969 0.26,0.177 10 false *c
*a String 1
*b Mark A
*c Mark B


Secure string 1 so that it passes through marks A and B on the left and right sides.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.




b.

Extend the vehicle center line (string 2).

i.

Hang a weight with a pointed tip so that it passes through the center of the front emblem and accurately mark the center position on the road surface. (Mark C)

E432417C01
1.042,1.594 1.76,1.323 true 2.031,2.125 1.781,2.125 true 3.938,2.469 3.615,2.313 false 3.938,2.563 3.583,2.563 false 2.031,2.042 2.271,2.208 0.24,0.167 10 true *a 3.448,2.198 3.76,2.354 0.313,0.156 10 false *b 0.813,1.583 1.031,1.76 0.219,0.177 10 true *c 3.396,2.469 3.708,2.625 0.313,0.156 10 false *e 1.979,0.531 2.219,0.698 0.24,0.167 10 true *d 1.323,0.531 1.563,0.698 0.24,0.167 10 true *d
*a String *b Weight
*c Center *d Bilateral Symmetry
*e Mark C - -



ii.

Hang a weight with a pointed tip from the center of the rear emblem and accurately mark the center position on the road surface. (Mark D)

E432418C01
4.688,1.573 5.396,1.323 true 5.417,1.885 5.885,1.885 true 2.823,2.542 3.167,2.396 true 2.823,2.635 3.229,2.635 false 5.958,1.802 6.156,1.979 0.198,0.177 10 true *a 3.219,2.281 3.531,2.438 0.313,0.156 10 false *b 4.51,1.5 4.688,1.677 0.177,0.177 10 true *c 5.021,0.51 5.24,0.688 0.219,0.177 10 true *d 5.583,0.51 5.802,0.688 0.219,0.177 10 true *d 3.281,2.552 3.594,2.708 0.313,0.156 10 false *e
*a String *b Weight
*c Center *d Bilateral Symmetry
*e Mark D - -



iii.
E287140C01
1.719,1.333 2.229,0.896 false 2.219,2.927 2.583,2.427 false 1,2.188 1.708,2.917 false 1.719,3.208 2.104,3.573 false 1.375,3.969 1.719,3.656 false 0.802,2.083 1.021,2.281 0.219,0.198 10 false *a 2.271,0.781 2.458,0.958 0.188,0.177 10 false *d 2.156,3.542 2.385,3.729 0.229,0.188 10 false *e 2.625,2.313 2.875,2.51 0.25,0.198 10 false *b 1.24,3.979 1.427,4.177 0.188,0.198 10 false *c
*a Datum Point
*b String 1
*c String 2
*d Mark C
*e Mark D


Secure string 2 so that it passes through marks C and D at the front and rear of the vehicle.

NOTICE:

When securing string 2, check that there is no slack and the string is not twisted.


HINT:

Set the point where strings 1 and 2 intersect as the datum point.





PROCEDURE 3: SET MARKERS (when checking front)


a.
E287141C01
1.719,1.208 2.24,0.76 false 2.594,3.448 2.333,3.156 false 2.01,4.104 1.708,3.76 false 1.125,3.781 1.323,3.781 1.323,3.781 1.719,3.156 false 0.583,1.917 0.771,1.74 0.771,1.74 0.99,1.74 false 1.031,1.667 1.281,1.865 0.25,0.198 10 false *a 2.302,0.677 2.583,0.875 0.281,0.198 10 false *e 2.635,3.479 2.865,3.656 0.229,0.177 10 false *c 2.063,4.125 2.281,4.292 0.219,0.167 10 false *d 0.958,3.708 1.208,3.885 0.25,0.177 10 false *b
*a 5000 mm (16.4 ft.)
*b Datum Point
*c String 1
*d String 2
*e Mark E


In front of the vehicle, extend string 3 perpendicular to the vehicle center line (string 2) and place a marker.

i.

Mark the position on string 2 in front of the vehicle, 5000 mm (16.4 ft.) from the datum point. (Mark E)


ii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



iv.
E287142C01
0.771,0.927 1.094,1.25 false 1.115,1.656 1.396,1.25 false 2.281,1.688 2.042,1.25 false 2.688,1.438 2.313,1.25 false 2.688,0.573 2.583,0.573 2.583,0.573 2.458,1.25 false 2.042,4.073 1.719,3.76 false 2.521,3.51 2.198,3.198 false 1.938,0.938 2.094,0.448 2.094,0.448 2.25,0.448 false 1.417,0.938 1.26,0.51 1.26,0.51 1.104,0.51 false 0.917,0.417 1.115,0.583 0.198,0.167 10 false *a 0.594,0.823 0.802,1.01 0.208,0.188 10 false *g 0.938,1.635 1.167,1.792 0.229,0.156 10 false *e 2.333,1.688 2.51,1.833 0.177,0.146 10 false *f 2.74,1.427 2.979,1.583 0.24,0.156 10 false *h 2.74,0.5 2.948,0.656 0.208,0.156 10 false *d 2.583,3.531 2.792,3.688 0.208,0.156 10 false *b 2.083,4.073 2.292,4.24 0.208,0.167 10 false *c 2.292,0.354 2.521,0.51 0.229,0.156 10 false *a
*a 1400 mm (4.59 ft.)
*b String 1
*c String 2
*d String 3
*e Mark F
*f Mark G
*g Mark H
*h Mark I


Secure string 3 so that it passes through marks F and G as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



v.

Mark positions on string 3, 1400 mm (4.59 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I).


vi.
E287109C01
0.75,1.667 1.063,1.25 false 2.333,1.667 1.917,1.125 false 1.083,1.083 0.833,0.833 false 2.052,1.083 1.833,0.333 false 1.385,1.083 1.167,0.5 false 2.323,0.635 2.323,0.333 2.323,0.333 2.583,0.333 false 2.333,1.083 2.667,0.75 2.667,0.75 2.833,0.75 false 3.25,1.333 3.25,1.104 3.25,1.104 3.052,1.104 false 2.781,1.708 2.365,1.229 false 0.604,1.688 0.823,1.875 0.219,0.188 10 false *c 2.313,1.698 2.51,1.854 0.198,0.156 10 false *d 0.677,0.688 0.896,0.865 0.219,0.177 10 false *g 1.052,0.354 1.292,0.521 0.24,0.167 10 false *e 1.708,0.188 1.948,0.333 0.24,0.146 10 false *f 2.885,0.667 3.063,0.813 0.177,0.146 10 false *h 2.635,0.25 2.865,0.417 0.229,0.167 10 false *a 3.188,1.354 3.406,1.521 0.219,0.167 10 false *b 2.74,1.708 2.958,1.896 0.219,0.188 10 false *c
*a 800 mm (2.62 ft.)
*b 100 mm (0.33 ft.)
*c Cross Check Marker
*d Check Marker
*e Mark F
*f Mark G
*g Mark H
*h Mark I


Place and secure the cross check markers, centered on marks H and I.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.




vii.

Place the check marker between marks F and G.


viii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 4: SET MARKERS (When checking rear)


a.

To the rear of the vehicle, extend string 4 perpendicular to the vehicle center line (string 2) and place a check marker.

i.
E287143C01
1.719,1.104 2.208,0.854 false 0.948,2.26 1.167,2.26 1.167,2.26 1.719,2.844 false 1.229,4.021 1.688,3.573 false 0.698,3.104 0.896,3.104 0.896,3.104 1.094,3.271 false 2.74,3.24 2.552,2.833 false 0.531,3.031 1.604,3.229 1.073,0.198 10 false *a 1.063,3.99 1.542,4.25 0.479,0.26 10 false *e 0.792,2.198 1.615,2.458 0.823,0.26 10 false *b 2.271,0.802 3.094,1.063 0.823,0.26 10 false *d 2.75,3.26 3.229,3.521 0.479,0.26 10 false *c
*a 1500 mm (4.92 ft.)
*b Datum Point
*c String 1
*d String 2
*e Mark J


Mark a position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


ii.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


iii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



iv.
E287144C01
1.708,0.896 2.208,0.542 false 0.583,2.063 1.094,2.688 false 1,3.052 1.396,3.354 false 0.677,3.802 1.094,3.354 false 2.385,3.042 2.073,3.344 false 2.875,3.646 2.677,3.344 false 2.615,3.802 2.313,3.344 false 2.167,3.969 1.969,3.667 false 1.188,3.979 1.417,3.667 false 2.292,0.5 2.75,0.698 0.458,0.198 10 false *c 0.385,1.969 0.844,2.167 0.458,0.198 10 false *b 0.844,2.938 1.302,3.135 0.458,0.198 10 false *f 2.438,2.969 2.896,3.167 0.458,0.198 10 false *e 2.844,3.698 3.302,3.896 0.458,0.198 10 false *d 2.542,3.854 3,4.052 0.458,0.198 10 false *h 2.167,4.042 3.104,4.26 0.938,0.219 10 false *a 1.115,4 2.052,4.219 0.938,0.219 10 false *a 0.552,3.833 1.01,4.031 0.458,0.198 10 false *g
*a 1400 mm (4.59 ft.)
*b String 1
*c String 2
*d String 4
*e Mark K
*f Mark L
*g Mark M
*h Mark N


Secure string 4 so that it passes through marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



v.

Mark positions on string 4, 1400 mm (4.59 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


vi.
E287106C01
2.583,2.948 2.833,2.667 false 1.917,4.25 1.833,3.667 false 1.375,3.604 1.302,3.396 1.302,3.396 1.385,3.396 false 2.052,3.604 2.135,3.396 2.135,3.396 2.052,3.396 false 3.167,3.885 3.167,3.635 3.167,3.635 3.052,3.635 false 1.5,4 1.5,3.729 1.5,3.729 1.344,3.729 false 2.583,4.25 2.333,4.021 false 2.354,3.74 2.781,3.969 false 0.792,4.063 0.99,3.656 false 1.115,3.625 0.792,3.281 false 2.323,3.635 2.573,3.354 false 2.885,2.583 3.302,2.75 0.417,0.167 10 false *f 2.802,3.99 3.167,4.344 0.365,0.354 10 false *d 1.875,4.313 2.708,4.479 0.833,0.167 10 false *e 1.427,4.042 2.01,4.208 0.583,0.167 10 false *c 2.531,4.292 3.115,4.458 0.583,0.167 10 false *a 3.115,3.917 3.396,4.135 0.281,0.219 10 false *b 1.448,3.333 1.698,3.5 0.25,0.167 10 false *h 1.865,3.333 2.115,3.5 0.25,0.167 10 false *g 0.677,4.125 1.375,4.458 0.698,0.333 10 false *d 0.719,3.146 1.417,3.479 0.698,0.333 10 false *i 2.552,3.208 3.25,3.542 0.698,0.333 10 false *j
*a 800 mm (2.62 ft.)
*b 100 mm (0.33 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g Mark K
*h Mark L
*i Mark M
*j Mark N


Place and secure the cross check markers, centered on marks M and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




vii.

Place the check marker between marks K and L.


viii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 5: SET MARKERS (When checking left side)


a.

To the left side of the vehicle, extend string 5 parallel to the vehicle center line (string 2) and place a check marker.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 5000 mm (16.4 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 5000 mm (16.4 ft.) from the datum point. (Mark E)


ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287146C01
0.563,0.5 1.094,1.073 false 1.135,1.438 1.406,1.063 false 2.042,1.052 2.177,0.583 false 2.552,1.063 2.792,0.594 false 2.583,3.719 2.74,3.958 false 2.052,3.719 2.208,3.958 false 1.104,3.417 1.385,3.708 false 0.781,4.073 1.083,3.708 false 1.365,4.021 1.469,4.281 false 1.365,0.771 1.438,0.438 false 0.385,0.417 0.698,0.615 0.313,0.198 10 false *f 1.385,0.26 2.021,0.469 0.635,0.208 10 false *a 0.99,1.469 1.302,1.667 0.313,0.198 10 false *d 2.156,0.427 2.469,0.625 0.313,0.198 10 false *e 2.781,0.427 3.188,0.667 0.406,0.24 10 false *b 2.719,3.99 3.125,4.229 0.406,0.24 10 false *c 2.156,3.99 2.469,4.188 0.313,0.198 10 false *g 1.427,4.313 2.063,4.521 0.635,0.208 10 false *a 0.656,4.094 1.063,4.365 0.406,0.271 10 false *i 0.938,3.323 1.25,3.521 0.313,0.198 10 false *h
*a 1400 mm (4.59 ft.)
*b String 3
*c String 4
*d Mark F
*e Mark G
*f Mark H
*g Mark K
*h Mark L
*i Mark M


Secure strings 3 and 4 so that they pass through marks F and G, marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings 3 and 4, 1400 mm (4.59 ft.) to the left of the vehicle center line (string 2). (Marks H and M)


ix.
E395048C01
2.396,2.958 2.583,2.677 false 1.563,3.938 1.698,3.823 false 2.5,1 2.688,0.719 false 0.656,3.594 0.448,3.333 false 1.094,0.688 1.281,0.406 false 0.865,1.271 1.094,1.021 false 0.865,3.854 1.094,3.604 false 2.563,2.51 2.875,2.708 0.313,0.198 10 false *a 1.385,3.906 1.698,4.104 0.313,0.198 10 false *b 2.656,0.552 2.969,0.75 0.313,0.198 10 false *c 0.333,3.167 0.646,3.365 0.313,0.198 10 false *d 1.25,0.25 1.563,0.448 0.313,0.198 10 false *e 0.698,1.292 1.01,1.49 0.313,0.198 10 false *f 0.719,3.906 1.031,4.104 0.313,0.198 10 false *g
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f Mark H
*g Mark M


E287147C04
0.771,0.771 1.385,1.021 false 0.781,0.385 1.396,0.635 false 1.406,1.531 1.24,1.365 false 1.385,1.677 1.229,1.792 false 1.385,2.208 1.188,2.083 false 1.396,2.354 1.281,2.51 false 2.531,2.979 2.656,3.219 false 1.385,3.594 1.563,3.75 false 0.24,2.354 0.125,2.354 0.125,2.354 0.125,2.635 false 0.51,2.354 0.396,2.354 0.396,2.354 0.396,2.635 false 0.802,2.354 0.688,2.354 0.688,2.354 0.688,2.635 false 1.063,2.51 0.948,2.51 0.948,2.51 0.948,2.792 false 0.615,0.313 1.073,0.51 0.458,0.198 10 false *f 0.604,0.677 0.917,0.885 0.313,0.208 10 false *g 1.104,1.24 1.563,1.438 0.458,0.198 10 false *l 1.073,1.792 1.531,1.99 0.458,0.198 10 false *k 1.073,1.969 1.531,2.167 0.458,0.198 10 false *j 1.208,2.552 1.667,2.75 0.458,0.198 10 false *i 2.625,3.281 3.083,3.479 0.458,0.198 10 false *e 1.615,3.771 2.073,3.969 0.458,0.198 10 false *h 0.865,2.781 1.802,3.052 0.938,0.271 10 false *a 0.594,2.698 1.531,2.969 0.938,0.271 10 false *b 0.333,2.677 1.271,2.948 0.938,0.271 10 false *c 0.042,2.677 0.313,2.896 0.271,0.219 10 false *d
*a 1400 mm (4.59 ft.)
*b 1600 mm (5.25 ft.)
*c 3100 mm (10.17 ft.)
*d 3300 mm (10.82 ft.)
*e String 1
*f String 5
*g Mark H
*h Mark M
*i Mark O
*j Mark P
*k Mark Q
*l Mark R


Secure string 5 so that it passes through marks H and M as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.

Make marks on string 5 that are 1400 mm (4.59 ft.), 1600 mm (5.25 ft.), 3100 mm (10.17 ft.) and 3300 mm (10.82 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)


xi.
E287107C01
1.094,3.615 0.75,3.333 false 1.438,0.167 1.104,0.167 1.104,0.167 1.104,0.396 false 2,0.5 1.135,0.917 false 1.073,3.75 0.667,4.25 false 1.583,4 1.583,3.74 1.583,3.74 1.438,3.74 false 0.885,1.219 1.104,1.031 false 1.104,0.667 0.667,0.5 false 2.583,3.031 2.833,2.74 false 0.885,2.604 1.115,2.406 false 0.875,2.052 1.115,2.229 false 1.229,1.896 1.115,1.75 false 1.333,1.396 1.115,1.573 false 0.365,1.031 0.198,1.031 0.198,1.031 0.198,1.5 false 1.063,2.323 0.813,2.323 false 1.073,1.667 0.823,1.667 false 1.49,0.083 2.073,0.25 0.583,0.167 10 false *b 0.49,0.406 0.906,0.573 0.417,0.167 10 false *g 2.052,0.417 3.302,0.583 1.25,0.167 10 false *d 0.646,2.25 1.479,2.417 0.833,0.167 10 false *e 0.573,4.271 2.073,4.438 1.5,0.167 10 false *d 0.594,3.229 0.927,3.396 0.333,0.167 10 false *i 1.51,4.042 2.094,4.208 0.583,0.167 10 false *c 2.885,2.604 3.302,2.771 0.417,0.167 10 false *f 0.719,1.25 1.052,1.417 0.333,0.167 10 false *h 1.292,1.25 1.625,1.417 0.333,0.167 10 false *m 1.177,1.927 1.51,2.094 0.333,0.167 10 false *l 0.75,1.906 1.083,2.073 0.333,0.167 10 false *k 0.792,2.646 1.125,2.813 0.333,0.167 10 false *j 0.146,1.552 0.729,1.719 0.583,0.167 10 false *a 0.594,1.583 1.427,1.75 0.833,0.167 10 false *e
*a 100 mm (0.33 ft.)
*b 800 mm (2.62 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g String 5
*h Mark H
*i Mark M
*j Mark O
*k Mark P
*l Mark Q
*m Mark R


Place and secure the cross check markers, centered on marks H and M.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




xii.

Place check markers between marks O and P, and marks Q and R.


xiii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 6: SET MARKERS (When checking right side)


a.

At the right side of the vehicle, extend string 6 parallel to the vehicle and place a marker.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 5000 mm (16.4 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 5000 mm (16.4 ft.) from the datum point. (Mark E)


ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287712C01
0.927,0.49 1.344,1.052 false 2,1.063 2.229,1.469 false 2.313,1.063 2.792,0.385 false 2.5,1.063 2.896,1.323 false 2.813,3.615 2.906,3.354 false 2.313,3.635 2.573,3.948 false 2.01,3.615 2.219,3.354 false 1.354,3.625 1.125,3.344 false 1.969,3.938 2.094,4.188 false 1.99,0.76 2.146,0.448 false 2.115,0.313 3.188,0.51 1.073,0.198 10 false *a 2.052,4.229 3.125,4.427 1.073,0.198 10 false *a 0.708,0.385 1.021,0.583 0.313,0.198 10 false *d 2.833,0.24 3.146,0.438 0.313,0.198 10 false *f 2.969,1.302 3.417,1.531 0.448,0.229 10 false *b 2.26,1.5 2.573,1.698 0.313,0.198 10 false *e 2.948,3.271 3.396,3.5 0.448,0.229 10 false *c 2.271,3.271 2.583,3.469 0.313,0.198 10 false *g 2.594,3.979 2.906,4.177 0.313,0.198 10 false *i 0.896,3.219 1.208,3.417 0.313,0.198 10 false *h
*a 1400 mm (4.59 ft.)
*b String 3
*c String 4
*d Mark F
*e Mark G
*f Mark I
*g Mark K
*h Mark L
*i Mark N


Secure strings 3 and 4 so that they pass through marks F and G and marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings 3 and 4, 1400 mm (4.59 ft.) to the right of the vehicle center line (string 2). (Marks I and N)


ix.
E395049C01
2.51,2.948 2.688,2.656 false 1.51,3.906 1.719,3.813 false 2.573,0.99 2.719,0.74 false 0.688,3.594 0.458,3.313 false 2.313,0.688 2.49,0.396 false 2.313,1.01 2.604,1.354 false 2.313,3.594 2.604,3.938 false 2.667,2.5 2.979,2.698 0.313,0.198 10 false *a 1.323,3.875 1.635,4.073 0.313,0.198 10 false *b 2.698,0.594 3.01,0.792 0.313,0.198 10 false *c 0.302,3.156 0.615,3.354 0.313,0.198 10 false *d 2.5,0.229 2.813,0.427 0.313,0.198 10 false *e 2.646,1.365 2.958,1.563 0.313,0.198 10 false *f 2.635,3.938 2.948,4.135 0.313,0.198 10 false *g
*a String 1
*b String 2
*c String 3
*d String 4
*e String 6
*f Mark I
*g Mark N


E287713C14
2.01,0.781 2.365,0.573 false 1.823,0.729 2.021,1.021 false 2.26,1.333 2.021,1.531 false 2.229,1.833 2.031,1.667 false 1.885,2.01 2.01,2.219 false 1.896,2.531 2.01,2.344 false 0.656,3.125 0.771,3.125 0.771,3.125 0.875,2.969 false 2.99,2.76 2.99,2.563 2.99,2.563 3.167,2.563 false 1.854,3.792 2.01,3.615 false 2.448,2.75 2.448,2.552 2.448,2.552 2.604,2.552 false 2.729,2.75 2.729,2.552 2.729,2.552 2.885,2.552 false 2.177,2.74 2.177,2.542 2.177,2.542 2.333,2.542 false 1.646,0.615 1.958,0.813 0.313,0.198 10 false *g 2.427,0.51 2.958,0.75 0.531,0.24 10 false *f 2.313,1.229 2.625,1.427 0.313,0.198 10 false *l 2.219,1.865 2.531,2.063 0.313,0.198 10 false *k 1.802,1.802 2.115,2 0.313,0.198 10 false *j 1.833,2.552 2.146,2.75 0.313,0.198 10 false *i 0.438,3.042 0.906,3.292 0.469,0.25 10 false *e 1.677,3.76 1.99,3.958 0.313,0.198 10 false *h 2.927,2.792 3.26,3.021 0.333,0.229 10 false *d 2.677,2.792 2.969,3.031 0.292,0.24 10 false *c 2.104,2.792 3.063,3 0.958,0.208 10 false *a 2.385,2.792 3.344,3 0.958,0.208 10 false *b
*a 1400 mm (4.59 ft.)
*b 1600 mm (5.25 ft.)
*c 3100 mm (10.17 ft.)
*d 3300 mm (10.82 ft.)
*e String 1
*f String 6
*g Mark I
*h Mark N
*i Mark S
*j Mark T
*k Mark U
*l Mark V


Secure string 6 so that it passes through marks I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.

Make marks on string 6 that are 1400 mm (4.59 ft.), 1600 mm (5.25 ft.), 3100 mm (10.17 ft.) and 3300 mm (10.82 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)


xi.
E287108C01
1.5,0.583 2.292,0.917 false 2.563,1.406 2.323,1.573 false 2.615,1.896 2.323,1.76 false 2.198,2.583 2.333,2.406 false 2.74,3.375 2.365,3.25 false 3.167,1.333 3.167,1.031 3.167,1.031 3.063,1.031 false 2.5,3.021 2.75,2.729 false 2.323,0.667 2.75,0.333 false 2.323,0.396 2.323,0.167 2.323,0.167 2.083,0.167 false 1.99,3.74 1.833,3.74 1.833,3.74 1.833,4.25 false 2.333,3.615 2.552,3.927 false 2.198,2.01 2.333,2.229 false 2.333,1.01 2.75,0.667 false 2.656,1.667 2.354,1.667 false 2.656,2.302 2.354,2.302 false 1.292,0.51 2.542,0.677 1.25,0.167 10 false *d 2.719,1.604 3.333,1.76 0.615,0.156 10 false *e 2.74,3.375 3.125,3.646 0.385,0.271 10 false *d 1.781,4.292 2.365,4.458 0.583,0.167 10 false *c 2.604,3.927 2.938,4.094 0.333,0.167 10 false *i 2.802,2.583 3.219,2.75 0.417,0.167 10 false *f 3.104,1.385 3.417,1.594 0.313,0.208 10 false *a 2.802,0.583 3.135,0.75 0.333,0.167 10 false *h 2.802,0.25 3.219,0.417 0.417,0.167 10 false *g 1.917,0.104 2.5,0.271 0.583,0.167 10 false *b 2.583,1.323 2.917,1.49 0.333,0.167 10 false *m 2.656,1.865 2.99,2.031 0.333,0.167 10 false *l 2.135,1.844 2.385,2.042 0.25,0.198 10 false *k 2.135,2.625 2.469,2.792 0.333,0.167 10 false *j 2.698,2.229 3.313,2.385 0.615,0.156 10 false *e
*a 100 mm (0.33 ft.)
*b 800 mm (2.62 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g String 6
*h Mark I
*i Mark N
*j Mark S
*k Mark T
*l Mark U
*m Mark V


Place and secure the cross check markers, centered on marks I and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




xii.

Place check markers between marks S and T, and marks U and V.


xiii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 7: SET MARKERS (When checking all cameras)


a.

Set markers in every direction from the vehicle.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 5000 mm (16.4 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 5000 mm (16.4 ft.) from the datum point. (Mark E)


ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287148C01
0.615,0.708 0.76,0.708 0.76,0.708 1.094,1.052 false 1.042,1.552 1.188,1.552 1.188,1.552 1.396,1.063 false 2.344,1.531 2.167,1.531 2.167,1.531 2.042,1.063 false 2.76,0.292 2.583,0.292 2.583,0.292 2.354,1.073 false 2.865,0.719 2.688,0.719 2.688,0.719 2.573,1.052 false 2.292,3.135 2.146,3.135 2.146,3.135 2.042,3.448 false 2.75,4.177 2.604,4.177 2.604,4.177 2.365,3.458 false 2.76,3.75 2.646,3.75 2.646,3.75 2.563,3.458 false 2.021,4.323 1.906,4.323 1.906,4.323 1.719,4.042 false 0.833,3.719 0.969,3.719 0.969,3.719 1.083,3.458 false 0.979,3.115 1.115,3.115 1.115,3.115 1.406,3.448 false 1.375,0.76 1.271,0.375 false 2,0.76 2.125,0.396 false 1.313,3.99 1.385,3.76 false 2.135,3.99 2.073,3.76 false 1.188,0.229 2.26,0.427 1.073,0.198 10 false *a 2.083,0.24 3.156,0.438 1.073,0.198 10 false *a 0.417,0.646 0.865,0.833 0.448,0.188 10 false *g 2.948,0.656 3.396,0.844 0.448,0.188 10 false *c 2.833,0.229 3.281,0.417 0.448,0.188 10 false *h 0.781,1.479 1.229,1.667 0.448,0.188 10 false *e 2.396,1.469 2.844,1.656 0.448,0.188 10 false *f 2.354,3.083 2.802,3.271 0.448,0.188 10 false *i 0.802,3.063 1.25,3.25 0.448,0.188 10 false *j 0.667,3.667 1.115,3.854 0.448,0.188 10 false *k 2.813,4.125 3.26,4.313 0.448,0.188 10 false *l 2.833,3.698 3.281,3.885 0.448,0.188 10 false *d 2.094,4.26 2.542,4.448 0.448,0.188 10 false *b 2.094,4.031 2.823,4.25 0.729,0.219 10 false *a 1.208,4.01 1.938,4.229 0.729,0.219 10 false *a
*a 1400 mm (4.59 ft.)
*b String 2
*c String 3
*d String 4
*e Mark F
*f Mark G
*g Mark H
*h Mark I
*i Mark K
*j Mark L
*k Mark M
*l Mark N


Secure strings 3 and 4 so that they pass through marks F, G, K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark string 3, 1400 mm (4.59 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I)


ix.

Mark string 4, 1400 mm (4.59 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


x.
E287132C02
1.094,0.688 1.292,0.271 false 2.302,0.667 2.688,0.177 false 2.604,1 2.875,0.677 false 2.625,1.375 2.302,1.01 false 0.781,1.385 1.104,1 false 0.458,3.26 0.698,3.583 false 0.771,4.031 1.094,3.594 false 1.552,3.833 1.708,3.74 false 2.646,3.948 2.313,3.594 false 2.635,2.646 2.469,2.958 false 1.344,0.198 1.802,0.396 0.458,0.198 10 false *e 2.75,0.104 3.208,0.302 0.458,0.198 10 false *f 2.938,0.604 3.396,0.802 0.458,0.198 10 false *c 2.688,1.396 3.146,1.594 0.458,0.198 10 false *h 0.625,1.417 1.083,1.615 0.458,0.198 10 false *g 0.313,3.104 0.771,3.302 0.458,0.198 10 false *d 0.646,4.073 1.104,4.271 0.458,0.198 10 false *i 1.375,3.875 1.833,4.073 0.458,0.198 10 false *b 2.667,4 3.125,4.198 0.458,0.198 10 false *j 2.729,2.573 3.188,2.771 0.458,0.198 10 false *a
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f String 6
*g Mark H
*h Mark I
*i Mark M
*j Mark N


Secure strings 5 and 6 so that they pass through marks H, M, I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



xi.
E288356C02
2.542,3.885 2.354,3.885 2.354,3.885 2.281,3.604 false 0.396,3.26 0.531,3.26 0.531,3.26 0.552,2.979 false 2.344,2.615 2.188,2.615 2.188,2.615 2.177,2.75 false 2.594,2.615 2.479,2.615 2.479,2.615 2.469,2.75 false 2.875,2.615 2.74,2.615 2.74,2.615 2.729,2.75 false 3.167,2.625 3.031,2.625 3.031,2.625 3.021,2.76 false 0.781,0.75 0.635,0.5 0.635,0.5 0.479,0.5 false 1.396,0.76 1.25,0.51 1.25,0.51 1.094,0.51 false 2.021,0.719 2.146,0.458 2.146,0.458 2.385,0.458 false 2.344,1.021 2.469,0.76 2.469,0.76 2.708,0.76 false 2.021,1.521 2.115,1.313 2.115,1.313 2.24,1.313 false 2.031,2.208 2.125,2 2.125,2 2.25,2 false 0.792,1.531 0.677,1.333 0.677,1.333 0.479,1.333 false 0.792,2.208 0.677,2.01 0.677,2.01 0.479,2.01 false 0.771,2.354 0.688,2.5 0.688,2.5 0.542,2.5 false 0.781,1.688 0.698,1.833 0.698,1.833 0.552,1.833 false 1.906,1.865 2.021,1.677 false 1.896,2.542 2.01,2.354 false 2.104,2.76 2.417,2.917 0.313,0.156 10 false *a 2.396,2.771 2.708,2.927 0.313,0.156 10 false *b 2.667,2.75 2.979,2.906 0.313,0.156 10 false *c 2.969,2.771 3.281,2.927 0.313,0.156 10 false *d 0.198,3.177 0.51,3.333 0.313,0.156 10 false *e 0.958,0.448 1.271,0.604 0.313,0.156 10 false *f 2.75,0.677 3.063,0.833 0.313,0.156 10 false *g 2.625,3.813 2.938,3.969 0.313,0.156 10 false *h 0.344,0.438 0.656,0.594 0.313,0.156 10 false *i 2.438,0.396 2.75,0.552 0.313,0.156 10 false *j 0.375,2.458 0.688,2.615 0.313,0.156 10 false *k 0.344,1.948 0.656,2.104 0.313,0.156 10 false *l 0.344,1.75 0.656,1.906 0.313,0.156 10 false *m 0.302,1.271 0.615,1.427 0.313,0.156 10 false *n 1.802,2.552 2.115,2.708 0.313,0.156 10 false *o 2.271,1.927 2.583,2.083 0.313,0.156 10 false *p 1.823,1.875 2.135,2.031 0.313,0.156 10 false *q 2.281,1.24 2.594,1.396 0.313,0.156 10 false *r
*a 1400 mm (4.59 ft.)
*b 1600 mm (5.25 ft.)
*c 3100 mm (10.17 ft.)
*d 3300 mm (10.82 ft.)
*e String 1
*f String 2
*g String 3
*h String 4
*i String 5
*j String 6
*k Mark O
*l Mark P
*m Mark Q
*n Mark R
*o Mark S
*p Mark T
*q Mark U
*r Mark V


Make marks on string 5 that are 1400 mm (4.59 ft.), 1600 mm (5.25 ft.), 3100 mm (10.17 ft.) and 3300 mm (10.82 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)


xii.

Make marks on string 6 that are 1400 mm (4.59 ft.), 1600 mm (5.25 ft.), 3100 mm (10.17 ft.) and 3300 mm (10.82 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)


xiii.

Place and secure the cross check markers, centered on marks H, I, M and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.



E287112C01
4.26,2.052 4.583,1.917 false 4.26,2.792 4.583,2.667 false 4.25,2.25 4.583,2.375 false 4.25,2.99 4.583,3.115 false 2.573,2.385 2.896,2.25 false 2.573,3.115 2.896,2.979 false 2.573,1.927 2.906,2.052 false 2.563,2.667 2.896,2.792 false 4.365,1.406 4.833,0.917 false 4.271,2.896 5.708,2.521 5.708,2.521 4.292,2.135 false 2.5,1.167 2.896,1.427 false 4.26,0.26 4.26,0.167 4.26,0.167 4.677,0.167 false 5.469,1.448 5.635,1.448 5.635,1.448 5.635,1.75 false 2.5,4.667 2.896,4.365 false 4.667,4.667 4.26,4.365 false 3.417,5.469 3.417,4.396 false 3.083,4.75 3.208,4.375 false 4.083,4.75 3.958,4.375 false 4.906,3.708 5.24,3.354 false 3.927,1.146 4.01,1.146 4.01,1.146 3.958,1.438 false 3.24,1.146 3.156,1.146 3.156,1.146 3.198,1.438 false 4.26,1.438 4.438,1.635 false 3.531,1.417 3.729,0.521 false 2.865,2.906 1.156,2.51 1.156,2.51 2.875,2.146 false 2.865,1.271 2.385,0.625 false 4.281,4.51 4.667,5.25 false 2.865,4.51 2.406,5.25 false 3.354,5.5 4.188,5.667 0.833,0.167 10 false *d 2.99,4.781 3.24,4.948 0.25,0.167 10 false *k 2.354,4.677 2.688,4.844 0.333,0.167 10 false *l 4.031,4.792 4.281,4.958 0.25,0.167 10 false *j 4.698,4.698 4.948,4.865 0.25,0.167 10 false *m 5.292,3.302 5.708,3.469 0.417,0.167 10 false *e 4.635,3.063 4.969,3.229 0.333,0.167 10 false *r 4.635,2.583 4.969,2.75 0.333,0.167 10 false *s 4.635,2.323 4.969,2.49 0.333,0.167 10 false *t 4.635,1.833 4.969,2 0.333,0.167 10 false *u 4.75,0.104 5.333,0.271 0.583,0.167 10 false *b 4.885,0.833 6.135,1 1.25,0.167 10 false *c 5.563,1.792 6.146,1.958 0.583,0.167 10 false *a 3.75,1.083 4.083,1.25 0.333,0.167 10 false *g 3.302,1.083 3.635,1.25 0.333,0.167 10 false *f 2.292,1.063 2.625,1.229 0.333,0.167 10 false *h 2.396,1.833 2.667,2.052 0.271,0.219 10 false *q 2.385,2.323 2.719,2.49 0.333,0.167 10 false *p 2.365,2.604 2.698,2.771 0.333,0.167 10 false *o 2.406,3.125 2.74,3.292 0.333,0.167 10 false *n 0.969,2.448 1.802,2.615 0.833,0.167 10 false *d 4.479,1.604 4.813,1.771 0.333,0.167 10 false *i 3.74,0.365 4.323,0.531 0.583,0.167 10 false *d 5.802,2.438 6.635,2.604 0.833,0.167 10 false *d 2.302,0.469 3.552,0.635 1.25,0.167 10 false *c 4.677,5.302 5.927,5.469 1.25,0.167 10 false *c 2.313,5.313 3.563,5.479 1.25,0.167 10 false *c
*a 100 mm (0.33 ft.) *b 800 mm (2.62 ft.)
*c Cross Check Marker *d Check Marker
*e String 1 *f Mark F
*g Mark G *h Mark H
*i Mark I *j Mark K
*k Mark L *l Mark M
*m Mark N *n Mark O
*o Mark P *p Mark Q
*q Mark R *r Mark S
*s Mark T *t Mark U
*u Mark V - -



xiv.

Place check markers between marks F and G, marks K and L, marks O and P, marks Q and R, marks S and T, and marks U and V.


xv.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 8: CAMERA VIEW ADJUSTMENT (CALIBRATION)


a.

Start diagnostic mode.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>DTC CHECK / CLEAR

NOTICE:

The following must be carried out with the engine running*1, hybrid system operating*2. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.

*1: for Gasoline Model

*2: for HV Model




b.
E422909

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E432763

Select "Camera Setting" on the "Function Check/Setting I" screen to display the Mode Setting screen.


d.
E432764

Select "View Adjustment" on the Mode Setting screen to display the adjustment screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



e.
E435680

After checking the screen, press the "NEXT" button on the "Signal Check" screen.

HINT:
·

When "CHK" (red) is displayed, perform the inspections.

·

If performing the adjustment after proceeding to the next screen, check that all items display "OK" (blue) before selecting "Next".




f.

Perform the view adjustment.

E432419C01
1.469,0.292 1.677,0.292 1.677,0.292 2.135,0.51 true 3.385,0.146 3.167,0.146 3.167,0.146 2.938,0.521 true 2.781,0.135 2.615,0.135 2.615,0.135 2.469,0.521 true 4.74,0.156 4.563,0.156 4.563,0.156 4.427,0.396 true 5.76,0.719 5.542,0.719 5.542,0.719 5.229,1.083 true 4.917,2.604 4.698,2.604 4.698,2.604 4.26,1.896 true 3.292,2.635 3.146,2.635 3.146,2.635 2.948,2.229 true 2.615,2.604 2.448,2.604 2.448,2.604 2.448,2.219 true 1.615,2.635 1.771,2.635 1.771,2.635 2.135,2.219 true 1.417,1.75 2.865,1.75 2.865,1.75 2.938,1.917 true 2.813,1.75 2.896,1.927 true 2.115,1.75 2.198,1.927 true 2.063,1.75 2.146,1.927 true 1.396,1.271 2.844,1.271 2.844,1.271 2.917,1.438 true 1.396,0.792 2.844,0.792 2.844,0.792 2.917,0.958 true 2.094,1.281 2.167,1.438 true 2.094,0.802 2.167,0.969 true 1.219,0.677 1.531,0.875 0.313,0.198 10 false *a 1.208,1.156 1.521,1.354 0.313,0.198 10 false *a 1.167,1.667 1.479,1.865 0.313,0.198 10 false *a 2.667,2.521 2.979,2.719 0.313,0.198 10 false *a 2.844,0.042 3.156,0.24 0.313,0.198 10 false *a 1.281,0.198 1.594,0.396 0.313,0.198 10 false *b 1.448,2.552 1.76,2.75 0.313,0.198 10 false *b 3.427,0.063 3.74,0.26 0.313,0.198 10 false *b 3.333,2.552 3.646,2.75 0.313,0.198 10 false *b 4.969,2.51 5.281,2.708 0.313,0.198 10 false *c 4.802,0.073 5.115,0.271 0.313,0.198 10 false *d 5.823,0.625 6.135,0.823 0.313,0.198 10 false *e
*a Red Line *b Cross Check Marker
*c Adjustment Button *d Camera Select Button
*e Height Control Button - -


NOTICE:

If replacing a camera, select the repaired camera and press "New Camera".


i.

Check that the cross check markers displayed on the adjustment screen appear connected.

E271143

NOTICE:
·

Before checking the adjustment screen, ensure that the check markers have been placed correctly.

·

If a cross check marker appears displaced on the adjustment screen, use the camera select buttons to select the corresponding camera, and then use the adjustment buttons or vehicle height adjustment buttons to adjust the screen.

E432420E01
4.781,0.323 6.604,0.573 1.823,0.25 10 false After selecting the button 5.479,1.896 6.844,2.135 1.365,0.24 10 false button selected 0.885,1.917 2.688,2.167 1.802,0.25 10 false When selecting button 5.479,3.656 6.896,3.885 1.417,0.229 10 false button selected 5.479,5.458 6.615,5.656 1.135,0.198 10 false button selected 5.479,7.375 6.969,7.552 1.49,0.177 10 false button selected



HINT:

If adjustment is needed, select "All View Reset" button and reset all adjustment values.



ii.

Check the check marker is in the adjustment screen.

E271144

NOTICE:
·

Before checking the adjustment screen, ensure that the check markers have been placed correctly.

·

If a check marker appears displaced on the adjustment screen, use the camera select buttons to select the corresponding camera, and then use the adjustment buttons or vehicle height adjustment buttons to adjust the screen.

E432420E01
4.781,0.323 6.604,0.573 1.823,0.25 10 false After selecting the button 5.479,1.896 6.844,2.135 1.365,0.24 10 false button selected 0.885,1.917 2.688,2.167 1.802,0.25 10 false When selecting button 5.479,3.656 6.896,3.885 1.417,0.229 10 false button selected 5.479,5.458 6.615,5.656 1.135,0.198 10 false button selected 5.479,7.375 6.969,7.552 1.49,0.177 10 false button selected

HINT:

If performing adjustment again, select "All View Reset" to initialize the adjustment status.






g.
E372775

When all adjustments are completed, press "OK".


h.

If data writing ends normally, "The view data writing was completed." is displayed.


i.

Press "OK".




PROCEDURE 9: STEERING ANGLE SETTING


a.

Preparation for adjustment

i.

Park the vehicle with the steering wheel centered.

HINT:

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.



ii.

Adjust the tire pressure to the specified value(s).



b.

Start diagnostic mode.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>DTC CHECK / CLEAR

NOTICE:

The following must be carried out with the engine running*1, hybrid system operating*2. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.

*1: for Gasoline Model

*2: for HV Model




c.
E422909

Select "Function Check/Setting" on the "Service Menu" screen.


d.
E432763

Select "Camera Setting" on the "Function Check/Setting I" screen.


e.
E435681

Select "Steering Angle Setting" on the Mode Setting screen to display the Signal Check screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



f.
E435680

Select "Next" on the Signal Check screen to display the Steering Angle Setting screen.

NOTICE:
·

If "CHK" (red) is displayed for an item on the Signal Check screen, selecting "Next" will not change to the Steering Angle Setting screen.

·

Check the Signal Check screen when "CHK" (red) is displayed for an item on the Signal Check screen.




g.

Adjust the steering angle

i.
E432772

Check that the steering wheel is centered (approximately +/- 5 degrees or less) and then select "Steering Center Memorize".


ii.

Turn the steering wheel fully to the left and fully to the right, and then press "Max Steering Angle Memorize". (Turning right and then left is OK)


iii.

When "Max Steering Angle Memorize" is selected, the system beeps, the steering angle setting values (steering neutral point and maximum steering angle) are stored, and the Mode Setting screen is displayed again.

HINT:
·

A beep will sound to confirm that the adjustment values have been stored.

·

If all signals are input normally, the Mode Setting screen is displayed automatically after the maximum steering angle is stored.

·

If steering angle setting is incomplete, "OK" cannot be selected.

·

Even if no DTC is detected, a steering sensor malfunction may disable the use of "Max Steering Angle Memorize".

·

If selecting "Max Steering Angle Memorize" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL






i.

Check steering angle adjustment.

HINT:

If the steering angle has been adjusted, check the steering angle adjustment on the panoramic view monitor screen after finishing diagnosis mode.



j.

Check on the panoramic view monitor screen that the estimated course line moves until the steering wheel is fully turned to either the left or right.

HINT:

If the estimated course line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "Steering Center Memorize" and "Max Steering Angle Memorize" again.