Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

E301406E68
5.073,2.844 6.385,3.073 1.313,0.229 10 false Parking Assist ECU 5.073,2.688 5.531,2.885 0.458,0.198 10 false H20 5.302,2.135 5.979,2.354 0.677,0.219 10 false GND1 5.313,1.729 5.99,1.948 0.677,0.219 10 false ACC 5.323,1.313 6,1.531 0.677,0.219 10 false IG 5.313,0.885 5.99,1.104 0.677,0.219 10 false +B 5.104,0.781 5.26,0.979 0.156,0.198 10 false 1 5.115,1.188 5.271,1.385 0.156,0.198 10 false 3 5.104,1.625 5.26,1.823 0.156,0.198 10 false 2 5.115,2.021 5.271,2.219 0.156,0.198 10 false 4 3.229,1.073 4.76,1.271 1.531,0.198 10 false ECU-B NO. 2 3.219,1.5 4.75,1.698 1.531,0.198 10 false ECU-IG1 NO. 4 3.323,1.917 4.115,2.135 0.792,0.219 10 false ECU-ACC 0.854,0.875 3.458,1.073 2.604,0.198 10 false from Auxiliary Battery 0.844,1.292 3.448,1.49 2.604,0.198 10 false from IG1-NO. 1 Relay 1.177,1.708 3.781,1.906 2.604,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


HINT:

If the parking assist ECU does not operate due to a power source problem, other system DTCs may be stored due to a CAN communication interruption.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BODY GROUND)
a.

Disconnect the H20 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H20-4 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
a.

Disconnect the H20 parking assist ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H20-1 (+B) - H20-4 (GND1) Always*1 11 to 14 V
Ignition switch off*2
H20-2 (ACC) - H20-4 (GND1) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
H20-3 (IG) - H20-4 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


*1: for Gasoline Model

*2: for HV Model



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR