Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING (for Panoramic Moon Roof)
RM37A0E _59 Vehicle Exterior _086900 SLIDING ROOF / CONVERTIBLE _0419684 SLIDING ROOF HOUSING(for Panoramic Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Panoramic Moon Roof)  DISASSEMBLY  


PROCEDURE

Hide 63260J 1.REMOVE SLIDING ROOF DRIVE GEAR ASSEMBLY (for Sliding Roof)

a.
B565106

Disconnect the connector.


b.

Disengage the clamp.


c.

Remove the 2 bolts and sliding roof drive gear assembly.


Hide 63260H 2.REMOVE SLIDING ROOF DRIVE GEAR ASSEMBLY (for Roof Sunshade)

a.
B565107

Disconnect the connector.


b.

Remove the 2 bolts and sliding roof drive gear assembly.


Hide 82172 3.REMOVE NO. 2 ROOF WIRE

a.

Disconnect the connector.

B565108


b.

Disengage the 16 clamps to remove the No. 2 roof wire.


Hide 63251H 4.REMOVE SLIDING ROOF WEATHERSTRIP

a.

Using a heat light, heat the sliding roof weatherstrip and sliding roof housing sub-assembly.

Heating Temperature
Item Temperature
Sliding Roof Weatherstrip and Sliding Roof Housing Sub-assembly 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the sliding roof weatherstrip and sliding roof housing sub-assembly excessively.



b.

Disengage the 10 guides and remove the sliding roof weatherstrip.

B565109C01
0,0 0,0 false
V100155

Double-sided Tape - -



Hide 63209 5.REMOVE ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.

Disengage the claw and 2 guides.

B565110C01
4.406,0.927 4.802,0.802 false 5.885,1.333 6.146,1.427 false 1.792,1.458 1.76,1.75 false 1.281,1.333 1.344,1.635 false 0.667,1.188 0.552,1.479 false 0.417,1.125 0.302,1.417 false 1.292,1.656 1.604,1.813 0.313,0.156 10 false *b 0.469,1.49 0.781,1.646 0.313,0.156 10 false *b 0.208,1.427 0.521,1.583 0.313,0.156 10 false *a 1.708,1.771 2.021,1.927 0.313,0.156 10 false *a 4.844,0.677 5.156,0.833 0.313,0.156 10 false *a 6.188,1.344 6.5,1.5 0.313,0.156 10 false *a
*a Pin *b Guide



b.

Disengage the 2 pins and raise the roof wind deflector panel sub-assembly as shown in the illustration.


c.

Disengage the 2 pins to remove the roof wind deflector panel sub-assembly.


Hide 63306 6.REMOVE SUNSHADE TRIM SUB-ASSEMBLY

a.
B565111N01
2.573,2.427 2.729,2.625 0.156,0.198 10 true a 2.583,4.375 2.74,4.573 0.156,0.198 10 true a

Slide the sunshade trim sub-assembly as shown in the illustration.

Standard:
Area Dimension
a 30 mm (1.18 in.)



b.
B565112C01
2.073,2.833 2.563,3.115 true 2.594,3.052 2.906,3.25 0.313,0.198 10 false *a
*a Hexagon Wrench


Insert a 1.5 mm hexagon wrench into the sunshade trim sub-assembly as shown in the illustration.

NOTICE:

Make sure that the hexagon wrench does not fall out when removing the sunshade trim sub-assembly.



c.
B565113

Using a T25 "TORX" socket wrench, remove the 2 screws.


d.

Disengage the 2 guides.


e.
B565114C01
0.573,2.188 0.375,2.521 false 2.688,0.677 2.417,0.844 false 0.25,2.521 0.563,2.677 0.313,0.156 10 false *a 2.719,0.583 3.031,0.74 0.313,0.156 10 false *b 0.188,1.323 0.344,1.521 0.156,0.198 10 false 1 0.833,1.813 0.99,2.01 0.156,0.198 10 true 2
*a Pin
*b Guide


Using a screwdriver, disengage the pin as indicated by the arrows, in the order shown in the illustration.


f.

Disengage the guide to remove the sunshade trim sub-assembly from the sliding roof housing sub-assembly.