Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING (for Panoramic Moon Roof)
RM37A0E _59 Vehicle Exterior _086900 SLIDING ROOF / CONVERTIBLE _0419684 SLIDING ROOF HOUSING(for Panoramic Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Panoramic Moon Roof)  REASSEMBLY  


PROCEDURE

Hide 63306 1.INSTALL SUNSHADE TRIM SUB-ASSEMBLY

a.

Engage the guide so that the hexagon wrench (*A) or locking pin (*B) is upright as shown in the illustration.

B565115C01
4.438,0.656 4.563,1.365 true 6.156,1.052 5.865,1.125 true 6.146,2.24 5.854,2.375 true 0.99,2.25 1.052,2.375 true 5.354,0.25 5.604,0.5 0.25,0.25 12 true *A 5.344,1.49 5.594,1.74 0.25,0.25 12 true *B 0.385,0.948 0.542,1.146 0.156,0.198 10 true 1 0.771,1.625 0.927,1.823 0.156,0.198 10 true 2 5.677,1.031 5.875,1.24 0.198,0.208 10 true *a 5.688,2.271 5.906,2.469 0.219,0.198 10 true *b 4.5,1.375 4.813,1.573 0.313,0.198 10 false *c 1.063,2.365 1.271,2.552 0.208,0.188 10 true *d
*A When Reusing the Sunshade Trim Sub-assembly *B When Replacing the Sunshade Trim Sub-assembly
*a Hexagon Wrench *b Locking Pin
*c Guide *d Pin


NOTICE:

Make sure that the hexagon wrench (*A) or locking pin (*B) does not fall out when installing the sunshade trim sub-assembly.



b.

Push the pin in the direction indicated by the arrow (1) shown in the illustration.


c.

Move the sunshade trim sub-assembly in the direction indicated by the arrow (2) shown in the illustration and engage the pin.


d.
B565116C01
0.781,0.396 1.021,0.25 false 0.156,2.156 0.427,1.583 true 2.354,0.438 2.708,0.365 true 1.042,0.156 1.354,0.313 0.313,0.156 10 false *a 0.063,2.177 0.375,2.333 0.313,0.156 10 false *b 2.74,0.271 3.052,0.427 0.313,0.156 10 false *b
*a Sunshade Cover
*b End of Sunshade Cover


Wrap the sunshade cover as shown in the illustration.


e.

Insert the ends of the sunshade cover into the sliding roof housing sub-assembly as shown in the illustration.


f.

Engage the 2 guides.


g.

Using a T25 "TORX" socket wrench, install the sunshade trim sub-assembly to the sliding roof housing sub-assembly with the 2 screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


h.

Remove the 1.5 mm hexagon wrench (*A) or locking pin (*B) as shown in the illustration.

B565117C01
2.094,2.26 2.604,2.542 true 5.594,2.26 6.073,2.573 true 0.167,0.094 0.563,0.333 0.396,0.24 12 false *A 3.521,0.083 3.833,0.333 0.313,0.25 12 false *B 2.625,2.458 2.938,2.615 0.313,0.156 10 false *a 6.094,2.5 6.406,2.656 0.313,0.156 10 false *b
*A When Reusing the Sunshade Trim Sub-assembly *B When Replacing the Sunshade Trim Sub-assembly
*a Hexagon Wrench *b Locking Pin



i.
B565118N01
2.667,3.177 2.823,3.375 0.156,0.198 10 true a 2.646,1.156 2.813,1.333 0.167,0.177 10 true a

Slide the sunshade trim sub-assembly as shown in the illustration.

Standard:
Area Dimension
a 30 mm (1.18 in.)



Hide 63209 2.INSTALL ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.

Engage the 2 pins (A) and lower the roof wind deflector panel sub-assembly as shown in the illustration.

B565119C01
0.594,1.521 1.01,1.458 true 2.052,1.917 2.344,2.094 true 4.417,1.833 4.302,2.146 false 4.198,1.74 4.042,2.042 false 5.177,1.844 5.375,1.615 false 5.542,2.063 5.604,2.427 false 1.042,1.365 1.354,1.521 0.313,0.156 10 false *a 3.927,2.063 4.24,2.219 0.313,0.156 10 false *b 2.365,2.01 2.677,2.167 0.313,0.156 10 false *a 4.219,2.156 4.531,2.313 0.313,0.156 10 false *c 5.563,2.448 5.875,2.604 0.313,0.156 10 false *b 5.385,1.49 5.698,1.646 0.313,0.156 10 false *c
*a Pin (A) *b Pin (B)
*c Guide - -



b.

Engage the 2 pins (B).


c.

Engage the claw and 2 guides to install the roof wind deflector panel sub-assembly.

NOTICE:

Make sure that the claw is securely engaged.



Hide 63251H 3.INSTALL SLIDING ROOF WEATHERSTRIP

a.

Clean the sliding roof housing sub-assembly surface.

i.

Using a heat light, heat the sliding roof housing sub-assembly surface.

Heating Temperature
Item Temperature
Sliding Roof Housing Sub-assembly 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the sliding roof housing sub-assembly excessively.



ii.

Remove the double-sided tape from the sliding roof housing sub-assembly.


iii.

Clean off any tape adhesive residue with cleaner.



b.

Coat the installation surface of the sliding roof housing sub-assembly with primer.


c.

Engage the 10 guides to temporarily install a new sliding roof weatherstrip.

B565120C01
0.583,0.646 0.51,0.531 false 1.448,2.031 1.563,1.844 false 6.792,0.646 6.885,0.5 false 5.094,2.031 4.979,1.802 false 1.542,1.698 1.854,1.896 0.313,0.198 10 false *a 0.406,0.375 0.719,0.573 0.313,0.198 10 false *a 6.833,0.365 7.146,0.563 0.313,0.198 10 false *a 4.865,1.656 5.177,1.854 0.313,0.198 10 false *a
*a Release Paper - -
V100155

Double-sided Tape - -



d.

Remove the release paper from the sliding roof weatherstrip as shown in the illustration and install the sliding roof weatherstrip.

HINT:

Press the sliding roof weatherstrip firmly to install it.



Hide 82172 4.INSTALL NO. 2 ROOF WIRE

a.

Engage the 16 clamps to install the No. 2 roof wire.

B565108


b.

Connect the connector.


Hide 5.ADJUST FULLY CLOSED POSITION

a.

Using a screwdriver, slide the sliding roof shoe sub-assembly in either direction and align the alignment mark with the edge of the sliding roof rail sub-assembly as shown in the illustration.

B565121C01
0.615,0.854 0.875,1.021 true 1.479,0.781 1.698,0.635 true 1.49,1.094 1.719,1.385 true 5.458,1.969 5.646,1.844 true 6.458,2.229 6.26,2.073 true 6.26,1.802 6.417,1.677 true 0.406,0.729 0.615,0.896 0.208,0.167 10 true *a 1.656,1.417 1.875,1.573 0.219,0.156 10 true *b 1.719,0.521 1.917,0.698 0.198,0.177 10 true *c 5.313,1.969 5.521,2.135 0.208,0.167 10 true *a 6.479,2.167 6.677,2.344 0.198,0.177 10 true *c 6.438,1.563 6.635,1.74 0.198,0.177 10 true *b
*a Sliding Roof Shoe Sub-assembly *b Alignment Mark
*c Edge of Sliding Roof Rail Sub-assembly - -


HINT:

Tape the screwdriver tip before use.



Hide 63260H 6.INSTALL SLIDING ROOF DRIVE GEAR ASSEMBLY (for Roof Sunshade)

a.
B565107

Install the sliding roof drive gear assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Connect the connector.


Hide 63260J 7.INSTALL SLIDING ROOF DRIVE GEAR ASSEMBLY (for Sliding Roof)

a.
B565106

Install the sliding roof drive gear assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Engage the clamp.


c.

Connect the connector.