Home › Engine / Hybrid System › 2GR-FKS (LUBRICATION) › OIL LEVEL SENSOR
RM37A0E _51 Engine / Hybrid System _086856 2GR-FKS LUBRICATION _0419964 OIL LEVEL SENSOR A

2GR-FKS LUBRICATION  OIL LEVEL SENSOR  INSTALLATION  


PROCEDURE

Hide 89491 1.INSTALL ENGINE OIL LEVEL SENSOR

a.

Install the engine oil level sensor to the oil pan sub-assembly with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install a new clip to the engine oil level sensor.


Hide 15104 2.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12102A 3.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.
A366163C02
1.104,0.563 1.656,0.563 true 0.917,0.469 1.229,0.625 0.313,0.156 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan sub-assembly within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.
A366064C02
2.208,0.438 2.583,0.635 0.375,0.198 10 true *a 0.073,1.458 0.313,1.698 0.24,0.24 10 false *a
*a Nut


Temporarily install the No. 2 oil pan sub-assembly with the 15 bolts and 2 nuts.


c.
A451632N01
2.208,0.438 2.365,0.635 0.156,0.198 10 true A

Tighten the nut (A).

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.
A451633C01
2.292,2.76 2.448,2.406 2.448,2.406 2.667,2.406 false 1.427,2.292 1.74,2.448 0.313,0.156 10 false *a 0.104,1.365 0.292,1.583 0.188,0.219 10 false B 2.708,2.313 3.021,2.542 0.313,0.229 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the nut (B).

SST
09961-00950  

Torque:
Specified tightening torque : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 5.2 N*m (53 kgf*cm, 46 in.*lbf)




e.
A451634N01
2,0.052 2.156,0.25 0.156,0.198 10 true 9 2.26,0.74 2.417,0.938 0.156,0.198 10 true 7 2.219,1.104 2.427,1.302 0.208,0.198 10 true 13 2.198,1.365 2.354,1.563 0.156,0.198 10 true 3 2.063,1.74 2.271,1.938 0.208,0.198 10 true 15 1.865,1.948 2.021,2.146 0.156,0.198 10 true 1 1.25,2.031 1.458,2.177 0.208,0.146 10 true 11 0.635,1.979 0.792,2.177 0.156,0.198 10 false 5 0.344,1.813 0.552,2.01 0.208,0.198 10 false 14 0.115,1.156 0.271,1.354 0.156,0.198 10 false 8 0.271,0.771 0.427,0.969 0.156,0.198 10 false 6 0.469,0.583 0.656,0.771 0.188,0.188 10 true 12 0.802,0.5 0.927,0.688 0.125,0.188 10 true 2 0.792,0.271 0.979,0.469 0.188,0.198 10 true 10 1,0 1.125,0.188 0.125,0.188 10 true 4

Tighten the 15 bolts in several steps in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 5.INSPECT FOR ENGINE OIL LEAK

Hide 51443C 7.INSTALL REAR ENGINE UNDER COVER RH