Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › COMBINATION SWITCH
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420007 COMBINATION SWITCH G

HYBRID / BATTERY CONTROL  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84720J 1.INSPECT EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)

a.

Check the resistance.

i.
C425587C02
1.5,0.25 1.813,0.479 0.313,0.229 1.281,1.781 1.417,1.375 true 2.177,1.802 2.052,1.375 true 0.073,0.073 0.49,0.406 0.417,0.333 10 false *a 1.229,1.781 1.5,1.99 0.271,0.208 10 false S 2.146,1.813 2.417,2.021 0.271,0.208 10 false E 1.563,0.271 1.875,0.469 0.313,0.198 10 false P9
*a Component without harness connected
(EV Drive Mode Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P9-5 (S) - P9-2 (E) EV drive mode switch (pattern select switch assembly) being pushed and held Below 50 Ω
EV drive mode switch (pattern select switch assembly) not pushed 10 kΩ or higher


If the result is not as specified, replace the EV drive mode switch (pattern select switch assembly).



b.

Check illumination.

i.
C425587C03
1.5,0.229 1.833,0.479 0.333,0.25 2.51,1.771 2.26,1.365 true 0.927,1.781 1.229,1.365 true 0.073,0.073 0.49,0.406 0.417,0.333 10 false *a 1.573,0.25 1.844,0.458 0.271,0.208 10 false P9 2.448,1.792 2.823,2.021 0.375,0.229 10 false ILL- 0.823,1.792 1.198,2.01 0.375,0.219 10 false ILL+
*a Component without harness connected
(EV Drive Mode Switch (Pattern Select Switch Assembly))


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the EV drive mode switch (pattern select switch assembly).

OK:
Condition Specified Condition
Battery positive (+) → P9-6 (ILL+)
Battery negative (-) →P9-1 (ILL-)
Illuminates


If the result is not as specified, replace the EV drive mode switch (pattern select switch assembly).



Hide 84721C 2.INSPECT TRAIL SWITCH (PATTERN SELECT SWITCH)

a.
C425587C04
1.531,0.229 1.854,0.458 0.323,0.229 1.281,1.771 1.417,1.365 true 2.177,1.792 2.052,1.365 true 0.073,0.073 0.49,0.406 0.417,0.333 10 false *a 1.24,1.792 1.51,2 0.271,0.208 10 false B 2.135,1.813 2.406,2.021 0.271,0.208 10 false E 1.604,0.26 1.917,0.458 0.313,0.198 10 false P8
*a Component without harness connected
(Trail Switch (Pattern Select Switch))


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-5 (B) - P8-2 (E) Trail switch (pattern select switch) being pushed and held Below 1 Ω
Trail switch (pattern select switch) not pushed 10 kΩ or higher


If the result is not as specified, replace the trail switch (pattern select switch).



b.

Check illumination.

i.
C425587C06
1.5,0.229 1.833,0.479 0.333,0.25 2.51,1.771 2.26,1.365 true 0.927,1.781 1.229,1.365 true 0.073,0.073 0.49,0.406 0.417,0.333 10 false *a 1.573,0.25 1.844,0.458 0.271,0.208 10 false P8 2.448,1.792 2.823,2.021 0.375,0.229 10 false ILL- 0.823,1.792 1.198,2.01 0.375,0.219 10 false ILL+
*a Component without harness connected
(Trail Switch (Pattern Select Switch))


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the trail switch (pattern select switch).

OK:
Condition Specified Condition
Battery positive (+) → P8-6 (ILL+)
Battery negative (-) →P8-1 (ILL-)
Illuminates


If the result is not as specified, replace the trail switch (pattern select switch).



Hide 84720A 3.INSPECT DRIVE MODE SELECT SWITCH (NO. 1 PATTERN SELECT SWITCH ASSEMBLY)

a.

Check the resistance.

i.
C426844C03
1.583,1.479 1.885,1.698 0.302,0.219 2.292,2.656 2.927,2.656 true 2.177,3.271 1.865,3.271 1.865,3.271 1.865,2.76 true 1.24,3.26 1.521,3.26 1.521,3.26 1.521,2.75 true 0.385,1.51 0.698,1.708 0.313,0.198 10 false *a 2.969,2.573 3.125,2.771 0.156,0.198 10 false E 2.219,3.177 2.375,3.375 0.156,0.198 10 false E 0.958,3.167 1.417,3.365 0.458,0.198 10 false SEL 1.635,1.49 2.094,1.688 0.458,0.198 10 false P3
*a Component without harness connected
(Drive Mode Select Switch (No. 1 Pattern Select Switch Assembly))
V113147

"DRIVE +" Side
V113148

"DRIVE -" Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-7 (SEL) - P3-5 (E) Pushed and held at "DRIVE +" side Below 50 Ω
Released (neutral position) 10 kΩ or higher
P3-6 (E) - P3-5 (E) Pushed and held at "DRIVE -" side Below 50 Ω
Released (neutral position) 10 kΩ or higher


If the result is not as specified, replace the drive mode select switch (No. 1 pattern select switch assembly).



b.

Check illumination.

i.
C427038C02
1.5,0.104 1.823,0.344 0.323,0.24 0.708,0.292 0.979,0.292 0.979,0.292 1.198,0.875 true 2.698,0.292 2.448,0.292 2.448,0.292 2.167,0.865 true 0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 2.75,0.219 3.365,0.417 0.615,0.198 10 false ILL+ 0.438,0.208 1.052,0.406 0.615,0.198 10 false ILL- 1.563,0.135 2.021,0.333 0.458,0.198 10 false P3
*a Component without harness connected
(Drive Mode Select Switch (No. 1 Pattern Select Switch Assembly))


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the drive mode select switch (No. 1 pattern select switch assembly).

OK:
Condition Specified Condition
Auxiliary battery positive (+) → P3-1 (ILL+)
Auxiliary battery negative (-) → P3-4 (ILL-)
Illuminates


If the result is not as specified, replace the drive mode select switch (No. 1 pattern select switch assembly).