CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Reconnect the instrument panel junction block assembly connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| MB-31 (BECU) - Body ground | Auxiliary battery power supply | Ignition switch off*1
Always*2 |
11 to 14 V |
| MB-32 (IG) - Body ground | Ignition power supply (IG signal) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| MB-30 (ACC) - Body ground | Ignition power supply (ACC signal) | Ignition switch off | Below 1 V |
| Ignition switch ACC | 11 to 14 V | ||
| MB-11 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| H42-19 (GND2) - Body ground | Ground | Always | Below 1 Ω |
| H43-1 (FLCY) - Body ground | Front door courtesy light switch assembly (for LH) input | Front door LH closed | 10 kΩ or higher |
| Front door LH open | Below 1 Ω | ||
| H43-6 (FRCY) - Body ground | Front door courtesy light switch assembly (for RH) input | Front door RH closed | 10 kΩ or higher |
| Front door RH open | Below 1 Ω | ||
| MB-13 (LCTY) - Body ground | Rear door courtesy light switch assembly (for LH) input | Rear door LH closed | 10 kΩ or higher |
| Rear door LH open | Below 1 Ω | ||
| MB-2 (RCTY) - Body ground | Rear door courtesy light switch assembly (for RH) input | Rear door RH closed | 10 kΩ or higher |
| Rear door RH open | Below 1 Ω | ||
| H43-30 (HCTY) - Body ground | Engine hood courtesy switch input | Engine hood open | 10 kΩ or higher |
| Engine hood closed | Below 1 Ω | ||
| MB-4 (BCTY) - Body ground | Back door courtesy light switch input | Back door closed | 10 kΩ or higher |
| Back door open | Below 1 Ω |
*1: for HV Model
*2: for Gasoline Model
Install the main body ECU (multiplex network body ECU) to instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| 4B-13 (LSFL) - Body ground | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V |
| Front door LH locked | 11 to 14 V | ||
| 4B-12 (LSFR) - Body ground | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V |
| Front door RH locked | 11 to 14 V | ||
| H44-18 (L2) - Body ground | Driver door key-linked lock input | Driver door key cylinder turned to lock position | Below 1 V |
| Driver door key cylinder off | 11 to 14 V | ||
| H44-17 (UL3) - Body ground | Driver door key-linked unlock input | Driver door key cylinder turned to unlock position | Below 1 V |
| Driver door key cylinder off | 11 to 14 V | ||
| 4B-14 (LSWL) - Body ground | Rear door LH unlock detection switch input | Rear door LH unlocked | Below 1 V |
| Rear door LH locked | 11 to 14 V | ||
| H43-17 (LSWR) - Body ground | Rear door RH unlock detection switch input | Rear door RH unlocked | Below 1 V |
| Rear door RH locked | 11 to 14 V | ||
| 4A-20 (SH) - Body ground | Security horn assembly drive | Security horn assembly sounding
(Theft deterrent system in alarm sounding state) |
Pulse generation
(Below 1 V ← → 11 to 14 V) |
| 4C-27 (HORN) - Body ground | Vehicle horn drives | Vehicle horn sounding
(Theft deterrent system in alarm sounding state) |
Pulse generation
(Below 1 V ← → 11 to 14 V) |