Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0420032 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is built into the hood lock assembly. This switch turns on when the engine hood is closed and turns off when the engine hood is opened.

WIRING DIAGRAM

B472053E43
5.427,2.063 7.094,2.438 1.667,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.823,1.531 2.656,1.917 1.833,0.385 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.844,1.01 6.281,1.24 0.438,0.229 10 false HCTY 5.573,1.01 6.01,1.24 0.438,0.229 10 false 30 2.021,1.01 2.458,1.24 0.438,0.229 10 false 1 0.969,1.01 1.406,1.24 0.438,0.229 10 false 2 5.438,1.896 5.875,2.125 0.438,0.229 10 false H43 0.833,1.375 1.271,1.604 0.438,0.229 10 false A21 1.833,1.01 2.271,1.24 0.438,0.229 10 false + 1.146,1.031 1.583,1.26 0.438,0.229 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS (HOOD COURTESY SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hood Courtesy SW Engine hood courtesy switch OFF or ON OFF: Engine hood closed
ON: Engine hood open
-
Body Electrical > Main Body > Data List
Tester Display
Hood Courtesy SW
50003 123 200
OK:

The GTS display changes correctly in response to the engine hood courtesy switch (hood lock assembly) status.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
2.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

OK

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

REPLACE ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the H43 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-1 (+) - H43-30 (HCTY) Always Below 1 Ω
A21-1 (+) or H43-30 (HCTY) - Other terminals and body ground Always 10 kΩ or higher
A21-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR