Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0420032 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B545433E06
0.823,0.156 2.656,0.354 1.833,0.198 10 false from Auxiliary Battery 2.333,1.865 2.948,2.063 0.615,0.198 10 false HORN 0.875,1.094 1.49,1.292 0.615,0.198 10 false HORN 6.115,0.844 6.729,1.042 0.615,0.198 10 false HORN 4.198,4.75 5.302,5.135 1.104,0.385 10 false Low Pitched Horn Assembly 4.438,1.917 6.052,2.323 1.615,0.406 10 false Instrument Panel Junction Block Assembly 5.375,3.396 7.052,3.927 1.677,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 2.021,0.844 2.24,1.042 0.219,0.198 10 false 1 2.938,0.833 3.156,1.031 0.219,0.198 10 false 2 3.875,4.521 4.094,4.719 0.219,0.198 10 false 1 4.198,4.573 4.552,4.771 0.354,0.198 10 false A10 4.792,4.031 7.104,4.25 2.313,0.219 10 false to Steering Pad Switch Assembly 5.865,0.823 6.219,1.021 0.354,0.198 10 false 28 5.365,3.208 5.719,3.406 0.354,0.198 10 false MB 6.74,1.021 7.094,1.219 0.354,0.198 10 false IC 4.635,0.729 4.99,0.927 0.354,0.198 10 false 27 4.604,0.938 4.958,1.135 0.354,0.198 10 false 4C 4.625,1.24 4.979,1.438 0.354,0.198 10 false 50 4.604,1.448 4.958,1.646 0.354,0.198 10 false 4A 2.938,1.448 3.156,1.646 0.219,0.198 10 false 3 2.031,1.448 2.25,1.646 0.219,0.198 10 false 5 2.583,4.76 3.729,5.156 1.146,0.396 10 false High Pitched Horn Assembly 2.583,4.604 2.938,4.802 0.354,0.198 10 false A11 2.271,4.51 2.49,4.708 0.219,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.INSPECT HORN
a.

Press the horn switch and check if the horn sounds.

Result:
Result Proceed to
Horn sounds A
Horn does not sound B




A

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B424477C23
1.333,0.25 1.75,0.5 0.417,0.25 4.813,0.5 5.229,0.75 0.417,0.25 6.271,1.083 6.271,1.406 6.271,1.406 5.833,1.406 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 1.448,0.292 1.76,0.49 0.313,0.198 10 false 4C 4.927,0.531 5.24,0.729 0.313,0.198 10 false MB 5.427,1.323 5.99,1.542 0.563,0.219 10 false HORN
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 4C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4C-27 - MB-28 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY