Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0420032 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn assembly to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B545427E06
0.792,0.135 2.938,0.333 2.146,0.198 10 false from Auxiliary Battery 0.719,1.073 1.969,1.271 1.25,0.198 10 false S-HORN 2.594,1.865 3.844,2.063 1.25,0.198 10 false S-HORN 4.375,1.625 5.979,2.385 1.604,0.76 10 false Instrument Panel Junction Block Assembly 4.146,3.74 4.635,3.958 0.49,0.219 10 false A20 4.146,3.896 6.25,4.219 2.104,0.323 10 false Security Horn Assembly 5.979,3.188 6.469,3.406 0.49,0.219 10 false MB 5.979,3.354 6.99,4.208 1.01,0.854 10 false Main Body ECU (Multiplex Network Body ECU) 4.375,1.469 4.865,1.688 0.49,0.219 10 false 4A 4.656,0.833 5.146,1.052 0.49,0.219 10 false 20 5.802,0.823 6.292,1.042 0.49,0.219 10 false 29 6.031,0.823 6.521,1.042 0.49,0.219 10 false SH 6.615,1.094 6.865,1.333 0.25,0.24 10 false IC 2.365,0.813 2.698,1.021 0.333,0.208 10 false 1 2.354,1.417 2.688,1.625 0.333,0.208 10 false 5 3.281,0.802 3.615,1.01 0.333,0.208 10 false 2 3.271,1.427 3.604,1.635 0.333,0.208 10 false 3 3.792,3.615 4.125,3.823 0.333,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY HORN)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn Security horn Assembly OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Security Horn
50004 123 20
OK:

The security horn assembly sounds and stops correctly when operated through the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY

OK

3.INSPECT S-HORN RELAY

NG

3.INSPECT S-HORN RELAY
a.
B256934C02
2.198,0.917 2.198,0.5 2.198,0.5 2.031,0.5 true 2.031,1.885 2.198,1.885 2.198,1.885 2.198,1.469 true 2.646,1.885 2.479,1.885 2.479,1.885 2.479,1.365 true 2.823,1 2.823,0.5 2.823,0.5 2.656,0.5 true 0.104,0.083 0.417,0.396 0.313,0.313 10 false *1 0.323,1.458 0.573,1.75 0.25,0.292 10 false 5 1.313,0.667 1.594,0.917 0.281,0.25 10 false 2 0.313,0.667 0.51,0.906 0.198,0.24 10 false 1 1.313,1.469 1.563,1.708 0.25,0.24 10 false 3 2.708,1.792 2.927,2.01 0.219,0.219 10 false 5 1.833,1.771 2.063,2 0.229,0.229 10 false 1 1.917,0.417 2.208,0.688 0.292,0.271 10 false 2 2.542,0.417 2.813,0.708 0.271,0.292 10 false 3
*1 S-HORN Relay


Remove the S-HORN relay from the No. 7 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE S-HORN RELAY

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B563002C01
1.333,0.219 1.75,0.469 0.417,0.25 4.833,0.5 5.25,0.75 0.417,0.25 6.375,1.083 6.375,1.406 6.375,1.406 5.938,1.406 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 1.448,0.25 1.76,0.448 0.313,0.198 10 false 4A 4.938,0.542 5.25,0.74 0.313,0.198 10 false MB 5.688,1.323 6.25,1.542 0.563,0.219 10 false SH
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-20 - MB-29 (SH) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - S-HORN RELAY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - S-HORN RELAY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 7 Relay Block


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S-HORN relay holder terminal 1 - Body ground Ignition switch off*1
Always*2
11 to 14 V
S-HORN relay holder terminal 5 - Body ground Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 7 Relay Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S-HORN relay holder terminal 3 - A20-1 Always Below 1 Ω
S-HORN relay holder terminal 3 or A20-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 7 Relay Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S-HORN relay holder terminal 2 - 4A-20 Always Below 1 Ω
S-HORN relay holder terminal 2 or 4A-20 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR