Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086891 MIRROR (EXT) _0420033 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  AUTO Power Retract Mirrors do not operate  


DESCRIPTION

The outer mirror switch assembly sends the auto retractable outer mirror switch signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends the auto retract/return signal to the outer mirror control ECU assemblies via CAN communication, which then controls the mirrors.

When the outer mirror control ECU assemblies receive a door lock output signal from the main body ECU (multiplex network body ECU) while the auto retractable outer mirror switch is on, the outer mirror control ECU assemblies operate the retract motors built into the outer rear view mirror assemblies to retract or return the outer rear view mirror assemblies.

WIRING DIAGRAM

B516898E08
0.51,5.385 2.448,5.615 1.938,0.229 10 false : CAN Communication Line 0.083,3.76 0.552,4 0.469,0.24 10 false J22 0.073,3.938 1.271,4.313 1.198,0.375 10 false Outer Mirror Switch Assembly 1.948,3.76 2.417,4 0.469,0.24 10 false H44 1.948,3.938 3.583,4.49 1.635,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 1.99,1.365 2.458,1.604 0.469,0.24 10 false RET 1.99,2.167 2.458,2.406 0.469,0.24 10 false AMR 1.99,3.01 2.458,3.25 0.469,0.24 10 false MIRE 1.063,3.021 1.531,3.26 0.469,0.24 10 false E2 0.938,2.198 1.406,2.438 0.469,0.24 10 false MAT 1.354,2.906 1.823,3.146 0.469,0.24 10 false 8 1.802,2.896 2.271,3.135 0.469,0.24 10 false 9 1.792,2.083 2.26,2.323 0.469,0.24 10 false 6 1.719,1.271 2.188,1.51 0.469,0.24 10 false 16 3.74,1.615 4.635,1.875 0.896,0.26 10 false z17 3.719,1.802 5.271,2.281 1.552,0.479 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.552,1.646 7,2.146 1.448,0.5 10 false Outer Rear View Mirror Assembly (Driver Door) 5.26,0.156 5.729,0.396 0.469,0.24 10 false 3 5.24,1.198 5.708,1.438 0.469,0.24 10 false 11 5.646,0.49 6.552,0.896 0.906,0.406 10 false Power Retract Mirror Motor 5.604,4.521 7.021,5.083 1.417,0.563 10 false Outer Rear View Mirror Assembly (Front Passenger Door) 3.729,4.688 5.271,5.229 1.542,0.542 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 4.948,1.302 5.417,1.542 0.469,0.24 10 false MF 4.927,3.146 5.396,3.385 0.469,0.24 10 false MR 4.927,4.188 5.417,4.417 0.49,0.229 10 false MF 4.938,0.25 5.406,0.49 0.469,0.24 10 false MR 3.74,4.5 4.635,4.76 0.896,0.26 10 false z16 5.26,4.063 5.729,4.302 0.469,0.24 10 false 11 5.271,3.021 5.74,3.26 0.469,0.24 10 false 3 5.646,3.365 6.552,3.771 0.906,0.406 10 false Power Retract Mirror Motor 1.01,1.375 1.479,1.615 0.469,0.24 10 false MR 1.344,1.271 1.813,1.51 0.469,0.24 10 false 10 1.354,2.083 1.823,2.323 0.469,0.24 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/o Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK POWER RETRACT MIRROR FUNCTION
a.

Check the power retract mirror function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/o Memory)>OPERATION CHECK

OK:

Power retract mirror function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Retractable Mirrors do not Operate with Power Retract Mirror Switch)

2.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the power door lock control system.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Power door lock control system is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

NG

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock control system.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Wireless door lock control system is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK ENTRY AND START SYSTEM (for Entry Function)

NG

4.CHECK ENTRY AND START SYSTEM (for Entry Function)
a.

Check the entry and start system (for Entry Function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>OPERATION CHECK

OK:

Entry and start system (for Entry Function) is normal.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS

NG

5.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto Mirror SW Retractable outer mirror switch signal OFF or ON OFF: Retractable outer mirror switch not in auto position
ON: Retractable outer mirror switch in auto position
-
Body Electrical > Main Body > Data List
Tester Display
Auto Mirror SW
50003 123 105
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT OUTER MIRROR SWITCH ASSEMBLY
6.INSPECT OUTER MIRROR SWITCH ASSEMBLY

OK

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H44 main body ECU (multiplex network body ECU).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J22-10 (MR) - H44-16 (RET) Always Below 1 Ω
J22-9 (MAT) - H44-6 (AMR) Always Below 1 Ω
J22-8 (E2) - H44-9 (MIRE) Always Below 1 Ω
J22-10 (MR) or H44-16 (RET) - Body ground Always 10 kΩ or higher
J22-9 (MAT) or H44-6 (AMR) - Body ground Always 10 kΩ or higher
J22-8 (E2) or H44-9 (MIRE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR