Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER BLOCK
RM37A0E _51 Engine / Hybrid System _086851 2GR-FKS ENGINE MECHANICAL _0420089 CYLINDER BLOCK A

2GR-FKS ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 15708 1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A366483

Using a 5 mm hexagon socket wrench, install the 3 No. 1 oil nozzle sub-assemblies to the cylinder block sub-assembly with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 2.INSTALL PISTON

HINT:

Perform this procedure only when replacement of the piston pin hole snap ring (rear side) is necessary.


a.

Using a screwdriver, install a new piston pin hole snap ring (rear side) at one end of the piston pin hole.


b.
A366517

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin with engine oil.

CAUTION:

Be sure to wear protective gloves.



d.
A366518C01
2.302,1.427 1.688,1.771 1.688,1.771 1.146,1.458 true 1.24,1.427 1.688,1.76 true 1.448,3.698 2.01,3.698 true 1.26,3.615 1.573,3.771 0.313,0.156 10 false *a 0.833,0.156 1.563,0.677 0.729,0.521 12 false *A 2.375,0.146 2.99,0.885 0.615,0.74 12 false *B 1.615,1.813 1.927,1.969 0.313,0.156 10 false *a
*A for Bank 1
*B for Bank 2
*a Front Mark


Align the front marks of the piston and connecting rod sub-assembly, and push in the piston pin with your thumb.

HINT:

The piston and piston pin are a matched set.



e.
A366520C01
2.25,1.948 2.354,1.708 true 2.115,1.927 2.427,2.083 0.313,0.156 10 false *a
*a Cutout


Using a screwdriver, install a new piston pin hole snap ring at the other end of the piston pin hole.

NOTICE:

Make sure that the end gap of the piston pin hole snap ring is not aligned with the cutout of the piston pin hole.



f.
A371542

Check the fitting condition between the piston and piston pin.

i.

Move the connecting rod back and forth on the piston pin. Check the fitting condition.

HINT:

If abnormal movement is felt, replace the piston and piston pin as a set.



ii.

Rotate the piston back and forth on the piston pin. Check the fitting condition.

HINT:
·

If abnormal movement is felt, replace the piston and piston pin as a set.

·

Perform Inspection After Repair after replacing the piston.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION





Hide 13011 3.INSTALL PISTON RING SET

a.

Install the oil ring expander and 2 side rails by hand.


b.
A411927C01
1.104,0.271 1.771,0.271 false 0.813,3.333 1.219,3.813 1.219,3.813 1.708,3.375 true 2.781,3.698 2.906,3.698 2.906,3.698 3.01,3.979 false 2.427,4.552 2.667,4.552 2.667,4.552 2.771,4.448 false 2.385,3.906 2.51,3.906 2.51,3.906 2.615,4.188 false 0.625,4.365 0.938,4.552 0.313,0.188 10 false *a 1.75,4.365 2.063,4.583 0.313,0.219 10 false *b 2.875,4.479 3.188,4.635 0.313,0.156 10 false *c 0.896,0.188 1.198,0.469 0.302,0.281 10 false *d 2.604,3.615 2.927,3.823 0.323,0.208 10 false *e 2.219,3.833 2.531,4.01 0.313,0.177 10 false *f 2.25,4.438 2.479,4.667 0.229,0.229 10 false *g 1.156,3.844 1.458,4.042 0.302,0.198 10 false *h
*a No. 1 Compression Ring
*b No. 2 Compression Ring
*c Oil Ring
*d Piston Ring Expander
*e Upper Side Rail
*f Oil Ring Expander
*g Lower Side Rail
*h Code Mark


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring as shown in the illustration.

NOTICE:
·

Install the No. 1 compression ring with the code mark (T1) facing upward.

·

Install the No. 2 compression ring with the code mark (T2) facing upward.




c.
A366522C01
1.135,1.552 0.604,1.656 0.604,1.656 1.135,1.448 true 2.281,3.646 2.708,3.938 true 0.927,1.917 1.24,2.073 0.313,0.156 10 false *a 0.917,0.438 1.229,0.594 0.313,0.156 10 false *b 0.177,0.104 0.771,0.573 0.594,0.469 12 false *A 1.635,0.073 1.948,0.229 0.313,0.156 10 false *d 0.625,1.167 0.938,1.323 0.313,0.156 10 false *e 1.646,2.177 1.958,2.333 0.313,0.156 10 false *f 1.615,4.427 1.927,4.583 0.313,0.156 10 false *f 1.646,2.323 1.958,2.479 0.313,0.156 10 false *d 2.396,2.646 2.708,2.802 0.313,0.156 10 false *b 2.354,4.104 2.667,4.26 0.313,0.156 10 false *a 2.74,3.906 3.052,4.063 0.313,0.156 10 false *c 2.698,3.375 3.01,3.531 0.313,0.156 10 false *e 0.438,1.573 0.75,1.729 0.313,0.156 10 false *c 0.208,2.385 0.771,2.885 0.563,0.5 12 false *B
*A for Bank 1
*B for Bank 2
*a No. 1 Compression Ring
*b No. 2 Compression Ring
*c Front Mark
*d Lower Side Rail
*e Oil Ring Expander
*f Upper Side Rail


Position the piston ring set so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.


HINT:

Perform Inspection After Repair after replacing the piston ring.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 11702 4.INSTALL CRANKSHAFT BEARING

a.
A366523C01
0.833,0.51 1.146,0.667 0.313,0.156 10 false *a 2.313,0.5 2.625,0.656 0.313,0.156 10 false *b 0.896,2.865 1.208,3.021 0.313,0.156 10 false *c 2.354,2.875 2.667,3.031 0.313,0.156 10 false *d
*a No. 1 and No. 4 Crankshaft Bearing
*b No. 2 and No. 3 Crankshaft Bearing
*c 20.9 mm
*d 17.9 mm


Clean the main journals and both surfaces of the crankshaft bearings.

NOTICE:

Crankshaft bearings come in widths of 17.9 mm (0.705 in.) and 20.9 mm (0.823 in.). Install the 20.9 mm (0.823 in.) crankshaft bearings to the No. 1 and No. 4 cylinder block journal positions. Install the 17.9 mm (0.705 in.) crankshaft bearings to the No. 2 and No. 3 positions.



b.
A366524C01
1.698,2.927 2.615,2.365 2.615,2.365 2.552,2.969 true 2.615,2.156 2.927,2.313 0.313,0.156 10 false *a 1.604,3.771 1.917,3.927 0.313,0.156 10 false *b 2.667,3.781 2.979,3.938 0.313,0.156 10 false *c
*a Upper Crankshaft Bearing
*b Correct
*c Incorrect


Install the upper crankshaft bearings.

i.

Install the upper crankshaft bearings to the cylinder block sub-assembly as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the crankshaft bearings or the contact surfaces.

·

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.





c.
A366525C01
2.052,2.073 2.229,2.5 true 1.052,2.042 0.604,2.208 false 1.896,1.896 2.208,2.052 0.313,0.156 10 false *a 0.417,2.146 0.729,2.302 0.313,0.156 10 false *b 0.729,2.938 0.885,3.135 0.156,0.198 10 false A 2.135,2.938 2.292,3.135 0.156,0.198 10 false B
*a Vernier Caliper
*b Number Mark


Install the lower crankshaft bearings.

i.

Install the lower crankshaft bearings to the crankshaft bearing caps.


ii.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and lower crankshaft bearing edge.

Difference Between (A) and (B):

0.7 mm (0.0276 in.) or less


NOTICE:
·

Do not apply engine oil to the crankshaft bearings or the contact surfaces.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.





Hide 11011 5.INSTALL CRANKSHAFT THRUST WASHER SET

a.

Apply engine oil to the crankshaft thrust washer set.


b.
A366526C01
2.104,1.51 2.094,0.563 2.094,0.563 1.313,1.25 true 2.052,0.365 2.365,0.521 0.313,0.156 10 true *a
*a Oil Groove


Install the crankshaft thrust washer set under the No. 2 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


Hide 13411 6.INSTALL CRANKSHAFT

a.

Apply engine oil to the crankshaft bearings, then place the crankshaft on the cylinder block sub-assembly.


b.
A366527C01
0.615,0.24 2.875,0.24 2.875,0.24 2.875,1.604 true 2.167,1.615 2.167,0.25 true 1.5,1.615 1.5,0.25 true 0.802,1.604 0.802,0.24 true 0.583,3.333 2.885,3.333 2.885,3.333 2.885,3.198 false 0.813,3.333 0.813,3.198 false 1.521,3.333 1.521,3.208 false 2.167,3.333 2.167,3.198 false 0.427,0.146 0.74,0.302 0.313,0.156 10 false *a 0.417,3.26 0.729,3.417 0.313,0.156 10 false *b
*a Projection
*b Number Mark


Confirm the projections and numbers of the crankshaft bearing caps and install the 4 crankshaft bearing caps to the cylinder block sub-assembly.

HINT:

A number is marked on each crankshaft bearing cap to indicate its installation position.



c.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap set bolts.


d.
A366528C01
0.375,2.906 1.083,2.135 true 0.24,2.896 0.552,3.052 0.313,0.156 10 false *a 1.583,3.719 1.896,3.875 0.313,0.156 10 false *b
*a Less than 6 mm
*b Bolt Length


Temporarily install the 8 crankshaft bearing cap set bolts to the inside positions.

Bolt Length:

100 to 102 mm (3.94 to 4.02 in.)



e.

Push the crankshaft bearing cap with your hand until the clearance between the crankshaft bearing cap and the cylinder block sub-assembly is less than 6 mm (0.236 in.) by using the 2 inside crankshaft bearing cap set bolts as a guide.


f.
A366529

Using a plastic hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.


g.

Apply a light coat of engine oil to the threads and under the heads of the 8 crankshaft bearing cap set bolts.


h.
A366530C01
1.563,3.719 1.875,3.875 0.313,0.156 10 false *a
*a Bolt Length


Temporarily install the 8 crankshaft bearing cap set bolts to the outside positions.

Bolt Length:

105.5 to 107.5 mm (4.15 to 4.23 in.)



i.

Install the crankshaft bearing cap set bolts.

HINT:

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.



j.

Step 1:

i.
A366236N03
0.219,1.573 0.438,1.802 0.219,0.229 10 true 16 0.865,1.604 1.083,1.865 0.219,0.26 10 true 12 2.385,1.604 2.604,1.844 0.219,0.24 10 true 10 3.063,1.594 3.333,1.896 0.271,0.302 10 true 14 3.052,1.219 3.281,1.458 0.229,0.24 10 true 6 3.083,0.958 3.302,1.188 0.219,0.229 10 true 5 3.031,0.604 3.26,0.854 0.229,0.25 10 true 13 2.385,0.573 2.542,0.771 0.156,0.198 10 true 9 2.385,0.917 2.615,1.156 0.229,0.24 10 true 1 2.385,1.208 2.615,1.458 0.229,0.25 10 true 2 0.885,0.552 1.094,0.771 0.208,0.219 10 true 11 0.844,0.896 1.083,1.156 0.24,0.26 10 true 3 0.865,1.188 1.104,1.427 0.24,0.24 10 true 4 0.229,0.594 0.458,0.844 0.229,0.25 10 true 15 0.208,0.927 0.427,1.177 0.219,0.25 10 true 7 0.281,1.208 0.438,1.406 0.156,0.198 10 true 8

Uniformly tighten the 16 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)

HINT:

If a crankshaft bearing cap bolt cannot be tightened to the specified torque, replace it.




k.

Step 2:

i.
A366532C01
2.198,0.594 2.625,0.323 true 2.656,0.229 2.969,0.385 0.313,0.156 10 false *a 1.333,0.438 1.646,0.594 0.313,0.156 10 false *b
*a Paint Mark
*b Turn 90°
V100136

Front of Engine


Mark the front of the crankshaft bearing cap set bolts with paint.


ii.

Tighten the crankshaft bearing cap set bolts 90° in the order shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



l.
A366235N03
2.083,1.802 2.24,2 0.156,0.198 10 true 8 2.51,1.375 2.667,1.573 0.156,0.198 10 true 5 2.854,1.042 3.01,1.24 0.156,0.198 10 true 6 3.271,0.833 3.427,1.031 0.156,0.198 10 true 7 1.313,0.177 1.469,0.375 0.156,0.198 10 true 4 1.031,0.448 1.188,0.646 0.156,0.198 10 true 1 0.656,0.719 0.813,0.917 0.156,0.198 10 true 2 0.365,1.615 0.521,1.813 0.156,0.198 10 true 3

Install 8 new seal washers and uniformly tighten the 8 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.

Torque:
51.5 N*m (525 kgf*cm, 38 ft.*lbf)


m.

Check that the crankshaft turns smoothly.


n.

Check the crankshaft thrust clearance.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>CYLINDER BLOCK>INSPECTION


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.

Install the connecting rod bearings to the connecting rod sub-assembly and connecting rod cap.


b.
A366534C01
0.51,3.104 0.75,3.635 true 0.375,2.906 0.688,3.063 0.313,0.156 10 false *a 1.948,3.281 2.104,3.479 0.156,0.198 10 false A 3.042,3.26 3.198,3.458 0.156,0.198 10 false B
*a Vernier Caliper


Using a vernier caliper, measure the distance between the connecting rod sub-assembly, connecting rod cap edges and the connecting rod bearing edge.

Difference Between (A) and (B):

0.7 mm (0.0276 in.) or less


NOTICE:

Do not apply engine oil to the connecting rod bearings or the contact surfaces.



Hide 8.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.
A366522C01
1.135,1.552 0.604,1.656 0.604,1.656 1.135,1.448 true 2.281,3.646 2.708,3.938 true 0.927,1.917 1.24,2.073 0.313,0.156 10 false *a 0.917,0.438 1.229,0.594 0.313,0.156 10 false *b 0.177,0.104 0.771,0.573 0.594,0.469 12 false *A 1.635,0.073 1.948,0.229 0.313,0.156 10 false *d 0.625,1.167 0.938,1.323 0.313,0.156 10 false *e 1.646,2.177 1.958,2.333 0.313,0.156 10 false *f 1.615,4.427 1.927,4.583 0.313,0.156 10 false *f 1.646,2.323 1.958,2.479 0.313,0.156 10 false *d 2.396,2.646 2.708,2.802 0.313,0.156 10 false *b 2.354,4.104 2.667,4.26 0.313,0.156 10 false *a 2.74,3.906 3.052,4.063 0.313,0.156 10 false *c 2.698,3.375 3.01,3.531 0.313,0.156 10 false *e 0.438,1.573 0.75,1.729 0.313,0.156 10 false *c 0.208,2.385 0.771,2.885 0.563,0.5 12 false *B
*A for Bank 1
*B for Bank 2
*a No. 1 Compression Ring
*b No. 2 Compression Ring
*c Front Mark
*d Lower Side Rail
*e Oil Ring Expander
*f Upper Side Rail


Position the piston ring set so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



c.

Using a piston ring compressor, push the piston and connecting rod sub-assembly into the cylinder with the front mark of the piston facing the front of the engine.

A366536C01
4.25,1.333 4.958,1.531 4.958,1.531 5.656,1.115 true 4.958,1.521 5.604,1.01 true 4.24,3.188 4.948,3.385 4.948,3.385 5.958,2.896 true 4.885,1.573 5.198,1.729 0.313,0.156 10 false *a 4.896,3.417 5.208,3.573 0.313,0.156 10 false *a 3.521,0.156 3.938,0.594 0.417,0.438 12 false *A 3.51,1.833 3.927,2.271 0.417,0.438 12 false *B
*A for Bank 1 *B for Bank 2
*a Front Mark - -
V100136

Front of Engine - -


NOTICE:

Match the connecting rod cap with the connecting rod sub-assembly.



d.
A366537C01
1.656,1.229 3.021,1.479 true 3.094,1.406 3.406,1.563 0.313,0.156 10 false *a
*a Front Mark
V100136

Front of Engine


Check that the front mark of the connecting rod cap is facing the front of the engine.


e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


f.

Install the 2 connecting rod bolts.

HINT:

The connecting rod bolts are tightened in 2 progressive steps.



g.

Step 1:

i.
A366538

Alternately tighten the 2 connecting rod bolts in several steps.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)



h.
A366539C01
2.146,0.698 2.719,0.458 true 2.76,0.344 3.073,0.5 0.313,0.156 10 false *a 1.302,0.458 1.615,0.615 0.313,0.156 10 false *b
*a Paint Mark
*b Turn 90°
V100136

Front of Engine


Step 2:

i.

Mark the front of each connecting rod bolt with paint.


ii.

Further tighten the connecting rod bolts 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



i.

Confirm that the crankshaft turns smoothly.


j.

Check the connecting rod thrust clearance.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>CYLINDER BLOCK>INSPECTION