Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420115 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a reclining motor position sensor signal despite the seat having been moved forward or rearward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2651 Reclining Sensor Malfunction Reclining motor position sensor signal not received when power seat moved forward or rearward
·

Position control ECU assembly (driver seat)

·

Reclining motor (separate type front seatback spring assembly (driver seat))

·

Wire harness or connector



WIRING DIAGRAM

B509695E93
1.146,2.479 2.219,2.698 1.073,0.219 10 false g5 4.802,1.063 5.26,1.26 0.458,0.198 10 false e24 4.813,0.542 5.271,0.74 0.458,0.198 10 false e23 4.802,2.083 5.26,2.281 0.458,0.198 10 false e25 4.802,1.573 5.26,1.771 0.458,0.198 10 false e25 5.219,0.542 5.833,0.74 0.615,0.198 10 false RCL+ 5.219,1.052 5.833,1.25 0.615,0.198 10 false RCL- 5.229,1.563 5.844,1.76 0.615,0.198 10 false SSRR 5.229,2.083 5.844,2.281 0.615,0.198 10 false SGND 1.146,2.656 2.833,2.854 1.688,0.198 10 false Reclining Motor 4.75,2.594 6.708,3.063 1.958,0.469 10 false Position Control ECU Assembly (Driver Seat) 0.552,3.083 2.448,3.656 1.896,0.573 10 false Separate Type Front Seatback Spring Assembly (Driver Seat) 4.844,0.313 5.052,0.521 0.208,0.208 10 false 10 4.896,0.823 5.052,1.021 0.156,0.198 10 false 6 4.844,1.333 5.156,1.531 0.313,0.198 10 false 11 4.833,1.844 5.146,2.042 0.313,0.198 10 false 12 2.323,1.458 3,1.708 0.677,0.25 10 false 2 2.323,0.438 2.938,0.719 0.615,0.281 10 false 4 2.313,0.958 3.042,1.198 0.729,0.24 10 false 1 2.313,1.979 3.125,2.281 0.813,0.302 10 false 3

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2651 is not output.



Result:
Result Proceed to
DTC B2651 is not output A
DTC B2651 output B



A

B

3.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING OPERATION)
3.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Reclining motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)

NG

7.INSPECT RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT))
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)
a.

Disconnect the g5 reclining motor (separate type front seatback spring assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
g5-2 - g5-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT))

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT)))
5.CHECK RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT))
a.
B517917C55
0.281,1.031 0.667,1.302 0.385,0.271 0.365,1.073 0.823,1.271 0.458,0.198 10 false g5 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a
*a Component with harness connected
(Reclining Motor (Separate Type Front Seatback Spring Assembly (Driver Seat)))


Reconnect the g5 reclining motor (separate type front seatback spring assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
g5-2 - Body ground Reclining motor operating 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT))

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the e25 position control ECU assembly (driver seat) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e25-11 (SSRR) - g5-2 Always Below 1 Ω
e25-11 (SSRR) or g5-2 - Body ground Always 10 kΩ or higher
e25-12 (SGND) - g5-3 Always Below 1 Ω
e25-12 (SGND) or g5-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT))

OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT)))

NG

REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT))

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the e23 and e24 position control ECU assembly (driver seat) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e23-10 (RCL+) - g5-4 Always Below 1 Ω
e23-10 (RCL+) or g5-4 - Body ground Always 10 kΩ or higher
e24-6 (RCL-) - g5-1 Always Below 1 Ω
e24-6 (RCL-) or g5-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR