When the position control ECU assembly (driver seat) does not receive a front vertical motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2652 | Front Vertical Sensor Malfunction | Front vertical motor position sensor signal not received when power seat moved upward or downward | ·
Position control ECU assembly (driver seat) ·
Front vertical motor (power seat tilt motor assembly (driver seat)) ·
Wire harness or connector |
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2652 is not output.
| Result | Proceed to |
|---|---|
| DTC B2652 is not output | A |
| DTC B2652 output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Tester Display |
|---|
| Front Vertical Operation |
Front vertical motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e12 front vertical motor (power seat tilt motor assembly (driver seat)) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e12-2 - e12-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Front Vertical Motor (Power Seat Tilt Motor Assembly (Driver Seat))) |
Reconnect the e12 front vertical motor (power seat tilt motor assembly (driver seat)) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e12-2 - Body ground | Front vertical motor operating | 4.5 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e25 position control ECU assembly (driver seat) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-10 (SSFV) - e12-2 | Always | Below 1 Ω |
| e25-10 (SSFV) or e12-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e12-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e12-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e23 and e24 position control ECU assembly (driver seat) connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-7 (FRV+) - e12-1 | Always | Below 1 Ω |
| e23-7 (FRV+) or e12-1 - Body ground | Always | 10 kΩ or higher |
| e24-4 (FRV-) - e12-4 | Always | Below 1 Ω |
| e24-4 (FRV-) or e12-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG