Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420117 SEAT HEATER SYSTEM U

SEAT  SEAT HEATER SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E407961C05
1.75,0.146 2.104,0.406 0.354,0.26 2.76,0.146 3.115,0.406 0.354,0.26 3.74,0.146 4.094,0.406 0.354,0.26 4.74,0.146 5.094,0.406 0.354,0.26 5.76,0.99 5.76,0.24 5.76,0.24 5.844,0.24 true 1.802,0.198 2.115,0.375 0.313,0.177 10 false H65 2.823,0.198 3.135,0.375 0.313,0.177 10 false H64 3.802,0.198 4.115,0.375 0.313,0.177 10 false H63 4.792,0.198 5.104,0.375 0.313,0.177 10 false H62 5.927,0.156 6.24,0.333 0.313,0.177 10 false *a
*a This connector is not used by the seat heater system. Refer to Air Conditioning System. - -


a.

Disconnect the H62 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H62-6 (IG+) - H62-17 (GND) IG power supply Ignition switch off Below 1 V
H62-6 (IG+) - H62-17 (GND) IG power supply Ignition switch ON 11 to 14 V
H62-5 (B) - H62-17 (GND) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
H62-17 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the H62 air conditioning amplifier assembly connector.


d.

Measure the voltage and check for pulses generation according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H64-12 (SM1R) - H62-17 (GND) Front seat heater control signal
·

Ignition switch ON

·

Front seat heater switch (air conditioning control assembly) on (LO)

(heater position)


Below 1 V
H64-13 (SM1L) - H62-17 (GND) Front seat heater control signal
·

Ignition switch ON

·

Front seat heater switch (air conditioning control assembly) on (LO)

(heater position)


Below 1 V
H64-23 (SM2R) - H62-17 (GND) Rear seat heater control signal
·

Ignition switch ON

·

Rear seat heater switch (Air conditioning control assembly No. 2) (RH) on


Below 1 V
H64-24 (SM2L) - H62-17 (GND) Rear seat heater control signal
·

Ignition switch ON

·

Rear seat heater switch (Air conditioning control assembly No. 2) (LH) on


Below 1 V
H62-7 (LIN1) - Body ground Seat heater switch signal Ignition switch ON Pulse generation



CHECK FRONT SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)


B567677N02
3.365,0.125 3.781,0.375 0.417,0.25 3.438,0.167 3.896,0.365 0.458,0.198 10 false H27

a.

Disconnect the H27 front seat heater switch (air conditioning control assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H27-6 (IG+) - H27-10 (GND) IG power supply Ignition switch off Below 1 V
H27-6 (IG+) - H27-10 (GND) IG power supply Ignition switch ON 11 to 14 V
H27-10 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the H27 front seat heater switch (air conditioning control assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H27-8 (LIN1) - H27-10 (GND) Front seat heater switch signal Ignition switch ON Pulse generation