Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM › 2020.02–2021.10
RM37A0E _58 Vehicle Interior _086894 SEAT _0420117 SEAT HEATER SYSTEM C

SEAT  SEAT HEATER SYSTEM  B14C0  Front Right Seat Heat Sensor Circuit  


DESCRIPTION

Output to the front seat cushion heater temperature sensor stops if one of the following occurs: 1) the temperature sensor is open or shorted; or 2) the temperature sensor is damaged and its output value does not change.

DTC No. Detection Item DTC Detection Condition Trouble Area
B14C0 Front Right Seat Heat Sensor Circuit Seat heater temperature sensor malfunction
·

Air conditioning amplifier assembly

·

Front seat cushion heater assembly RH

·

Wire harness or connector



WIRING DIAGRAM

B520543E16
2.052,0.24 2.51,0.438 0.458,0.198 10 false TSR 2,0.896 2.458,1.094 0.458,0.198 10 false SG-7 0.688,1.344 1.146,1.542 0.458,0.198 10 false H65 2.427,0.188 2.74,0.385 0.313,0.198 10 false 12 2.417,0.781 2.729,0.979 0.313,0.198 10 false 3 0.688,1.51 3.896,1.708 3.208,0.198 10 false Air Conditioning Amplifier Assembly 4.094,0.26 4.25,0.458 0.156,0.198 10 false 4 4.104,0.771 4.26,0.969 0.156,0.198 10 false 5 4.073,1.323 4.531,1.521 0.458,0.198 10 false e8 4.063,1.479 7.031,1.781 2.969,0.302 10 false Front Seat Cushion Heater Assembly RH 1.052,0.615 1.51,0.813 0.458,0.198 10 false 5 V

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B14C0 is not output.


Result:
Proceed to
OK
NG




OK

NG

3.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH
3.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH

OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT CUSHION HEATER ASSEMBLY RH)

NG

REPLACE FRONT SEAT CUSHION HEATER ASSEMBLY RH

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT CUSHION HEATER ASSEMBLY RH)
a.

Disconnect the H65 air conditioning amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H65-12 (TSR) - e8-4 Always Below 1 Ω
H65-12 (TSR) or e8-4 - Body ground Always 10 kΩ or higher
H65-3 (SG-7) - e8-5 Always Below 1 Ω
H65-3 (SG-7) or e8-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR