Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › PANORAMIC MOON ROOF SYSTEM
RM37A0E _59 Vehicle Exterior _086900 SLIDING ROOF / CONVERTIBLE _0420296 PANORAMIC MOON ROOF SYSTEM U

SLIDING ROOF / CONVERTIBLE  PANORAMIC MOON ROOF SYSTEM  TERMINALS OF ECU  


CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)


B567062N03
3.365,0.208 3.781,0.458 0.417,0.25 3.458,0.25 4.219,0.813 0.76,0.563 10 false R19

a.

Disconnect the R19 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
R19-8 (B) - R19-12 (E) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
R19-1 (IG) - R19-12 (E) IG power supply Ignition switch off Below 1 V
R19-1 (IG) - R19-12 (E) IG power supply Ignition switch ON 11 to 14 V
R19-12 (E) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the R19 sliding roof ECU (sliding roof drive gear assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
R19-7 (OPN) - R19-12 (E) Sliding roof open switch input signal Ignition switch ON, sliding roof open switch on Below 1 V
R19-7 (OPN) - R19-12 (E) Sliding roof open switch input signal Ignition switch ON, sliding roof open switch off 11 to 14 V
R19-5 (CLS) - R19-12 (E) Sliding roof close switch input signal Ignition switch ON, sliding roof close switch on Below 1 V
R19-5 (CLS) - R19-12 (E) Sliding roof close switch input signal Ignition switch ON, sliding roof close switch off 11 to 14 V
R19-2 (TILT) - R19-12 (E) Sliding roof tilt switch input signal Ignition switch ON, sliding roof tilt switch on Below 1 V
R19-2 (TILT) - R19-12 (E) Sliding roof tilt switch input signal Ignition switch ON, sliding roof tilt switch off 11 to 14 V
R19-4 (CLS) - R19-12 (E) Roof sunshade close switch input signal Ignition switch ON, roof sunshade close switch on Below 1 V
R19-4 (CLS) - R19-12 (E) Roof sunshade close switch input signal Ignition switch ON, roof sunshade close switch off 11 to 14 V
R19-6 (OPN) - R19-12 (E) Roof sunshade open switch input signal Ignition switch ON, roof sunshade open switch on Below 1 V
R19-6 (OPN) - R19-12 (E) Roof sunshade open switch input signal Ignition switch ON, roof sunshade open switch off 11 to 14 V



CHECK ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)


B567062N04
3.375,0.146 3.792,0.396 0.417,0.25 3.458,0.188 4.073,0.583 0.615,0.396 10 false R20

a.

Disconnect the R20 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
R20-8 (B) - R20-12 (E) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
R20-1 (IG) - R20-12 (E) IG power supply Ignition switch off Below 1 V
R20-1 (IG) - R20-12 (E) IG power supply Ignition switch ON 11 to 14 V
R20-12 (E) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the R20 roof sunshade ECU (sliding roof drive gear assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
R20-7 (OPN) - R20-12 (E) Sliding roof open switch input signal Ignition switch ON, sliding roof open switch on Below 1 V
R20-7 (OPN) - R20-12 (E) Sliding roof open switch input signal Ignition switch ON, sliding roof open switch off 11 to 14 V
R20-5 (CLS) - R20-12 (E) Sliding roof close switch input signal Ignition switch ON, sliding roof close switch on Below 1 V
R20-5 (CLS) - R20-12 (E) Sliding roof close switch input signal Ignition switch ON, sliding roof close switch off 11 to 14 V
R20-2 (TILT) - R20-12 (E) Sliding roof tilt switch input signal Ignition switch ON, sliding roof tilt switch on Below 1 V
R20-2 (TILT) - R20-12 (E) Sliding roof tilt switch input signal Ignition switch ON, sliding roof tilt switch off 11 to 14 V
R20-4 (CLS) - R20-12 (E) Roof sunshade close switch input signal Ignition switch ON, roof sunshade close switch on Below 1 V
R20-4 (CLS) - R20-12 (E) Roof sunshade close switch input signal Ignition switch ON, roof sunshade close switch off 11 to 14 V
R20-6 (OPN) - R20-12 (E) Roof sunshade open switch input signal Ignition switch ON, roof sunshade open switch on Below 1 V
R20-6 (OPN) - R20-12 (E) Roof sunshade open switch input signal Ignition switch ON, roof sunshade open switch off 11 to 14 V



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>TERMINALS OF ECU