Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › MULTI-TERRAIN SELECT SWITCH
RM37A0E _52 Drivetrain _086861 GF2A TRANSFER / 4WD / AWD _0420307 MULTI-TERRAIN SELECT SWITCH G

GF2A TRANSFER / 4WD / AWD  MULTI-TERRAIN SELECT SWITCH  INSPECTION  


PROCEDURE

Hide 84720A 1.INSPECT MULTI-TERRAIN SELECT SWITCH (NO. 1 PATTERN SELECT SWITCH ASSEMBLY) (for Dial Switch Type)

a.
C426215C01
1.188,1.906 1.354,1.906 1.354,1.906 1.354,1.323 true 2.26,1.906 2.094,1.906 2.094,1.906 2.094,1.323 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 1.021,1.833 1.198,2.031 0.177,0.198 10 false B 2.354,1.833 2.604,2.083 0.25,0.25 10 false E
*a Component without harness connected
(Multi-Terrain Select Switch (No. 1 Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (B) - 3 (E) NORMAL mode switch being pushed and held 80.4 to 83.6 Ω
NORMAL mode switch not pushed 10 kΩ or higher
6 (B) - 3 (E) ROCK & DIRT mode switch being turned and held 580.2 to 603.8 Ω
ROCK & DIRT mode switch not turned 10 kΩ or higher
6 (B) - 3 (E) MUD & SAND mode switch being turned and held 2.050 to 2.134 kΩ
MUD & SAND mode switch not turned 10 kΩ or higher


If the result is not as specified, replace the No. 1 pattern select switch assembly.


b.
C426215C02
2.51,1.885 2.344,1.885 2.344,1.885 2.344,1.333 true 0.938,1.885 1.104,1.885 1.104,1.885 1.104,1.333 true 2.594,1.802 2.927,2.052 0.333,0.25 10 false ILL- 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.625,1.802 0.979,2.104 0.354,0.302 10 false ILL+
*a Component without harness connected
(Multi-Terrain Select Switch (No. 1 Pattern Select Switch Assembly))


Apply battery voltage between the terminals of the switch and check the illumination condition of the multi-terrain select switch (No. 1 pattern select switch assembly).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → 7 (ILL+)
Battery negative (-) → 2 (ILL-)
Illuminates


If the result is not as specified, replace the No. 1 pattern select switch assembly.


Hide 84970D 2.INSPECT CRAWL CONTROL SWITCH ASSEMBLY (for Push Switch Type)

a.
C426215C01
1.188,1.906 1.354,1.906 1.354,1.906 1.354,1.323 true 2.26,1.906 2.094,1.906 2.094,1.906 2.094,1.323 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 1.021,1.833 1.198,2.031 0.177,0.198 10 false B 2.354,1.833 2.604,2.083 0.25,0.25 10 false E
*a Component without harness connected
(Crawl Control Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (B) - 3 (E) NORMAL mode switch being pushed and held 80.4 to 83.6 Ω
NORMAL mode switch not pushed 10 kΩ or higher
6 (B) - 3 (E) ROCK & DIRT mode switch being pushed and held 580.2 to 603.8 Ω
ROCK & DIRT mode switch not pushed 10 kΩ or higher
6 (B) - 3 (E) MUD & SAND mode switch being pushed and held 2.050 to 2.134 kΩ
MUD & SAND mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the crawl control switch assembly.


b.
C426215C02
2.51,1.885 2.344,1.885 2.344,1.885 2.344,1.333 true 0.938,1.885 1.104,1.885 1.104,1.885 1.104,1.333 true 2.594,1.802 2.927,2.052 0.333,0.25 10 false ILL- 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.625,1.802 0.979,2.104 0.354,0.302 10 false ILL+
*a Component without harness connected
(Crawl Control Switch Assembly)


Apply battery voltage between the terminals of the switch and check the illumination condition of the crawl control switch assembly.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → 7 (ILL+)
Battery negative (-) → 2 (ILL-)
Illuminates


If the result is not as specified, replace the crawl control switch assembly.